{
  "id": "shear-thinning",
  "title": "Shear Thinning",
  "lang": "en",
  "source_lang": "en",
  "summary": "Shear thinning is the decrease of a material’s apparent viscosity as its shear rate increases, commonly observed in polymer solutions, suspensions, and structured fluids.",
  "category": "science",
  "subcategory": "physics",
  "type": "concept",
  "aliases": [
    "Pseudoplasticity",
    "Pseudoplastic behavior",
    "Shear-thinning behavior"
  ],
  "generated_at": "2026-11-05",
  "model": "pro/gpt-6.1-sol",
  "url": "https://aiwiki.page/en/shear-thinning/",
  "translations": {
    "zh-Hans": {
      "url": "https://aiwiki.page/zh/shear-thinning/",
      "json": "https://aiwiki.page/zh/shear-thinning.json"
    }
  },
  "sections": [
    {
      "heading": "",
      "text": "Shear thinning is a flow behavior in which a material’s apparent viscosity decreases as the rate of shear deformation increases, under otherwise comparable conditions. It is common in polymer melts and solutions, concentrated suspensions, emulsions, paints, and many foods. A shear-thinning material therefore offers less resistance per unit shear rate when sheared more rapidly, although the total stress required to sustain the flow usually still increases. The behavior is often called pseudoplasticity, particularly when describing materials without a yield stress."
    },
    {
      "heading": "Definition and physical meaning",
      "text": "In simple shear flow, adjacent layers of material move parallel to one another at different velocities. For a velocity \\(u_x\\) varying with the transverse coordinate \\(y\\), the magnitude of the shear rate is\n\n\\[\\dot{\\gamma}=\\left|\\frac{\\partial u_x}{\\partial y}\\right|.\\]\n\nApparent viscosity is defined as\n\n\\[\\eta_{\\mathrm{app}}=\\frac{\\tau}{\\dot{\\gamma}},\\]\n\nwhere \\(\\tau\\) is the magnitude of the shear stress. Viscosity is measured in pascal-seconds, and shear rate in reciprocal seconds, within the International System of Units.\n\nA material is shear-thinning over a specified range when\n\n\\[\\frac{d\\eta_{\\mathrm{app}}}{d\\dot{\\gamma}}<0.\\]\n\nFor a Newtonian fluid, viscosity is independent of shear rate at fixed temperature, pressure, and composition. Shear thinning is one form of non-Newtonian behavior; its opposite is shear thickening.\n\nThe term describes a relationship between stress and deformation rate, not a decrease in density, a loss of material, or necessarily a permanent structural change. “Thinner” refers to lower apparent viscosity, not to a more dilute composition."
    },
    {
      "heading": "Microscopic mechanisms",
      "text": "Different materials can exhibit similar shear-thinning curves for different physical reasons.\n\nPolymers\n\nIn polymer solutions and melts, macromolecules continually change their configurations through thermal motion. At sufficiently low shear rates, they can relax substantially during deformation, and viscosity may remain nearly constant.\n\nWhen flow deforms chains faster than they can relax, their orientation and conformation change. Chain alignment and changes in the constraints imposed by neighboring chains can reduce resistance to further shear. The detailed mechanism depends on molecular architecture, concentration, molecular mass, and interactions with the solvent.\n\nThe relative importance of deformation and relaxation is often expressed by the Weissenberg number,\n\n\\[\\mathrm{Wi}=\\lambda\\dot{\\gamma},\\]\n\nwhere \\(\\lambda\\) is a characteristic relaxation time. Departures from the low-shear Newtonian regime often become appreciable when this quantity is of order unity, although real materials commonly have a range of relaxation times.\n\nSuspensions and structured liquids\n\nIn a colloidal dispersion, flow can alter particle arrangements or disrupt weakly associated clusters. If the resulting structure offers less resistance, apparent viscosity decreases. Competition between flow-induced rearrangement and Brownian motion is important for many small-particle dispersions.\n\nIn emulsions, droplets may deform, orient, and rearrange under shear. In associating solutions, reversible intermolecular networks may reorganize or partially break down. These processes need not involve irreversible chemical changes.\n\nNo single microscopic explanation applies to every shear-thinning material. Alignment, cluster disruption, droplet deformation, and network rearrangement can also occur together."
    },
    {
      "heading": "Mathematical descriptions",
      "text": "Power-law model\n\nA common empirical description is the Ostwald–de Waele, or power-law fluid, model:\n\n\\[\\tau=K\\dot{\\gamma}^{\\,n}, \\qquad \\eta_{\\mathrm{app}}=K\\dot{\\gamma}^{\\,n-1}.\\]\n\nHere \\(K\\) is the consistency index and \\(n\\) is the flow-behavior index:\n\n- \\(0<n<1\\): shear-thinning behavior;\n- \\(n=1\\): Newtonian behavior;\n- \\(n>1\\): shear-thickening behavior.\n\nFor \\(0<n<1\\), stress increases with shear rate, but less than proportionally. Thus, lower apparent viscosity does not generally mean that faster flow requires less stress.\n\nThe power-law model is useful over limited shear-rate intervals. It predicts an unbounded viscosity as shear rate approaches zero and a viscosity approaching zero at arbitrarily high shear rate, so it generally cannot describe an entire experimental flow curve. The units of \\(K\\), \\(\\mathrm{Pa\\,s^n}\\), also depend on \\(n\\).\n\nModels with viscosity plateaus\n\nMany materials exhibit a low-shear Newtonian plateau, an intermediate shear-thinning region, and sometimes an experimentally accessible high-shear plateau. The Carreau–Yasuda model represents this pattern as\n\n\\[\\eta(\\dot{\\gamma}) = \\eta_{\\infty} + (\\eta_0-\\eta_{\\infty}) \\left[1+(\\lambda\\dot{\\gamma})^a\\right]^{(n-1)/a}.\\]\n\nHere \\(\\eta_0\\) and \\(\\eta_{\\infty}\\) are the low- and high-shear limiting viscosities, \\(\\lambda\\) sets a transition timescale, and \\(a\\) controls the breadth of the transition. Such fits describe a flow curve but do not, by themselves, establish its microscopic cause.\n\nMaterials with a yield stress\n\nSome materials require a finite stress before sustained flow occurs. A common representation above the yield stress is the Herschel–Bulkley equation:\n\n\\[\\tau=\\tau_y+K\\dot{\\gamma}^{\\,n}.\\]\n\nFor \\(0<n<1\\), this combines a yield-stress contribution with shear-thinning behavior in the flowing state. Even when \\(n=1\\), the apparent viscosity decreases with shear rate because it contains the term \\(\\tau_y/\\dot{\\gamma}\\). Consequently, a falling apparent-viscosity curve alone does not establish the behavior of the post-yield contribution."
    },
    {
      "heading": "Distinction from related phenomena",
      "text": "Thixotropy. Thixotropy is a time-dependent, reversible decrease in viscosity under shear, followed by recovery under suitable conditions after shear is reduced or removed. Shear thinning describes dependence on shear rate; thixotropy describes dependence on time and deformation history. A material may exhibit either or both. A hysteresis loop in an increasing-and-decreasing shear-rate sweep can indicate time dependence, but is not sufficient by itself to identify its cause.\n\nViscoelasticity. Viscoelasticity combines viscous dissipation with elastic storage and recovery. Many polymeric liquids are both viscoelastic and shear-thinning, but the properties are distinct. A steady viscosity curve does not determine elastic normal stresses or transient stress relaxation.\n\nShear heating and degradation. Viscous heating can lower viscosity by raising temperature, while irreversible chain breakage can lower a polymer solution’s viscosity permanently. Neither should be mistaken for reversible shear-rate dependence under controlled conditions."
    },
    {
      "heading": "Measurement and interpretation",
      "text": "Shear thinning is commonly characterized using a rheometer with cone-and-plate, parallel-plate, or concentric-cylinder geometry. Capillary instruments are useful at higher shear rates and in processing-related studies. Measurements produce a flow curve of shear stress or apparent viscosity against shear rate.\n\nReliable interpretation requires attention to:\n\n- Temperature control: viscosity can be strongly temperature-dependent, and rapid shearing can generate heat.\n- Sample history: mixing, preshearing, rest periods, and elapsed time can change structured materials.\n- Steady-state criteria: measurements made before stress stabilizes can combine shear-rate effects with transient behavior.\n- Wall slip: motion at the sample–instrument interface can mimic reduced bulk viscosity.\n- Flow nonuniformity: edge fracture, particle migration, secondary flows, or localized deformation can invalidate a simple interpretation.\n- Instrument sensitivity: low stresses and high-rate inertial effects can limit the usable measurement range.\n\nReported values are therefore most informative when accompanied by temperature, geometry, preparation history, and the shear-rate interval. A single viscosity value is generally insufficient to characterize a shear-thinning material."
    },
    {
      "heading": "Applications and modeling limits",
      "text": "Shear thinning is useful when a product must resist motion at rest or under gentle deformation but flow readily during application or processing. Examples include paints that spread under a brush, printing inks, polymer melts passing through dies, and foods dispensed through narrow openings. Resistance to sagging or settling, however, may also depend on yield stress and structural recovery rather than shear thinning alone.\n\nIn industrial flow calculations, shear-rate-dependent viscosity affects pressure drop, mixing, coating thickness, and velocity profiles. Computational fluid dynamics can incorporate fitted constitutive equations, but predictions depend on whether those equations cover the relevant rates, temperatures, and flow histories.\n\nA viscosity model established in steady simple shear does not fully characterize behavior in stretching flows, rapidly changing flows, or strongly confined geometries. Such conditions may require measurements of extensional viscosity, elastic stresses, or structural evolution in addition to the shear-viscosity curve."
    }
  ],
  "links": [
    "viscosity",
    "shear-rate",
    "international-system-of-units",
    "newtonian-fluid",
    "temperature",
    "non-newtonian-fluid",
    "polymer",
    "solvent",
    "brownian-motion",
    "yield-stress",
    "viscoelasticity"
  ],
  "sources": [],
  "license": "https://creativecommons.org/licenses/by/4.0/"
}