{
  "id": "reaction-yield",
  "title": "Reaction Yield",
  "lang": "en",
  "source_lang": "en",
  "summary": "Reaction yield measures the amount of a specified product obtained from a chemical reaction, usually relative to the theoretical amount calculated from stoichiometry.",
  "category": "science",
  "subcategory": "chemistry",
  "type": "concept",
  "aliases": [
    "Chemical yield",
    "Synthetic yield"
  ],
  "generated_at": "2026-11-05",
  "model": "pro/gpt-6.1-sol",
  "url": "https://aiwiki.page/en/reaction-yield/",
  "translations": {
    "zh-Hans": {
      "url": "https://aiwiki.page/zh/reaction-yield/",
      "json": "https://aiwiki.page/zh/reaction-yield.json"
    }
  },
  "sections": [
    {
      "heading": "",
      "text": "Reaction yield describes the amount of a specified product obtained from a chemical reaction. It is commonly expressed as a percentage of the maximum amount predicted from the quantities of starting materials and the reaction’s stoichiometry. Yield connects the chemical transformation with its practical outcome: it reflects not only whether the desired product forms, but, depending on how it is measured, also how much survives handling, separation, and purification. A yield value is therefore meaningful only when the product, calculation basis, and measurement method are specified."
    },
    {
      "heading": "Definition and calculation",
      "text": "Three quantities are commonly distinguished:\n\n- Theoretical yield: the maximum amount of the specified product calculated from the starting materials, assuming that the intended reaction occurs completely without competing reactions or losses.\n- Actual yield: the amount of product obtained or measured in the experiment, expressed as an amount of substance or a mass.\n- Percentage yield: the actual yield divided by the theoretical yield, multiplied by 100.\n\nThus,\n\n\\[\\text{Percentage yield} = \\frac{\\text{actual yield}}{\\text{theoretical yield}} \\times 100\\%.\\]\n\nThe numerator and denominator must refer to the same substance and use compatible units. A ratio of product mass to starting-material mass is not generally a percentage reaction yield, because reactants and products can have different molar masses and stoichiometric coefficients.\n\nYield may also be reported as a fraction between zero and one. Expressions such as “yield” or “molar yield” sometimes denote other ratios, particularly in industrial and biochemical work, so their definitions must be stated explicitly.\n\nThe limiting reagent\n\nThe theoretical yield is normally determined by the limiting reagent: the reactant whose available amount permits the smallest extent of the intended reaction.\n\nFor a reaction written as\n\n\\[aA+bB\\rightarrow pP,\\]\n\nwith no product initially present, the theoretical amount of \\(P\\) is\n\n\\[n_{P,\\mathrm{theoretical}} = p\\min\\left( \\frac{n_{A,0}}{a}, \\frac{n_{B,0}}{b} \\right),\\]\n\nwhere \\(n_{A,0}\\) and \\(n_{B,0}\\) are the initial amounts of the reactants. The coefficients come from the balanced chemical equation, and amounts are commonly expressed in moles.\n\nFor example, suppose\n\n\\[2A+B\\rightarrow P\\]\n\nstarts with \\(0.100\\ \\mathrm{mol}\\) of \\(A\\) and \\(0.080\\ \\mathrm{mol}\\) of \\(B\\). Reactant \\(A\\) is limiting, giving a theoretical yield of \\(0.0500\\ \\mathrm{mol}\\) of \\(P\\). If the product has a molar mass of \\(150.0\\ \\mathrm{g\\,mol^{-1}}\\), its theoretical mass is \\(7.50\\ \\mathrm{g}\\). Obtaining \\(6.00\\ \\mathrm{g}\\) of pure product corresponds to an 80.0% yield.\n\nThis calculation is a stoichiometric upper bound, not a prediction that the reaction will reach that amount under the chosen conditions."
    },
    {
      "heading": "Ways of measuring yield",
      "text": "Isolated yield\n\nIsolated yield is based on product physically recovered after the reaction and subsequent processing. It is widely used in organic chemistry because it represents material available for further use.\n\nIsolation may involve extraction, filtration, crystallization, distillation, or chromatography. Each operation can lose some product. Consequently, isolated yield combines the efficiency of product formation with the efficiency of recovery.\n\nThe product’s composition also matters. Residual solvent, water, salts, or other impurities can increase the measured mass without increasing the amount of desired compound. If a reliable product mass fraction \\(w_P\\) is known, a purity-corrected yield can be calculated as\n\n\\[Y_{\\mathrm{corrected}} = \\frac{m_{\\mathrm{sample}}w_P} {m_{P,\\mathrm{theoretical}}} \\times100\\%.\\]\n\nThe chemical form must match the calculation: a free base, its salt, and a hydrated crystal have different molar masses.\n\nAnalytical or assay yield\n\nAnalytical yield measures product present in a sample or reaction mixture without necessarily isolating it. Methods include calibrated chromatography, quantitative nuclear magnetic resonance, and other forms of spectroscopy.\n\nAnalytical measurements require a valid relationship between instrument response and product quantity. Calibration, internal standards, representative sampling, and sample stability can all affect the result. A chromatographic peak-area percentage is not automatically a molar yield: different compounds may produce different detector responses, and some mixture components may not be detected.\n\nAn analytical yield can exceed the isolated yield because product remains in discarded liquid, adheres to equipment, or decomposes during purification. However, analytical yield is not inherently the more accurate value; its reliability depends on the method.\n\nCrude yield\n\nCrude yield refers to material recovered before full purification. Unless its composition is established, it may describe the mass of a mixture rather than the amount of the desired product. It is therefore not directly comparable with the isolated yield of a purified compound."
    },
    {
      "heading": "Yield, conversion, and selectivity",
      "text": "Yield is distinct from both conversion and selectivity.\n\nConversion measures the fraction of a specified reactant that has been consumed:\n\n\\[X_A = \\frac{n_{A,0}-n_A}{n_{A,0}}.\\]\n\nA high conversion does not necessarily mean a high yield of the desired product. The reactant may instead form unwanted products.\n\nSelectivity describes how much of the reacted material forms a particular product rather than alternatives. Several selectivity conventions exist, including ratios of desired to undesired products. Their numerical values are not interchangeable.\n\nWith a reactant-based fractional definition and appropriate stoichiometric normalization, yield can be written as\n\n\\[Y_P=X_A S_P.\\]\n\nFor the simple case in which one mole of \\(A\\) can produce one mole of \\(P\\),\n\n\\[S_P=\\frac{n_P}{n_{A,0}-n_A}, \\qquad Y_P=\\frac{n_P}{n_{A,0}}.\\]\n\nIf conversion is 90% and selectivity on this basis is 80%, the reaction-mixture yield is 72%. The isolated yield may be lower still.\n\nThese distinctions help separate three different causes of low yield: incomplete reaction, formation of competing products, and loss during recovery."
    },
    {
      "heading": "Factors affecting yield",
      "text": "Equilibrium and reaction rate\n\nA reversible reaction may reach chemical equilibrium before the limiting reagent is fully consumed. Its attainable product amount then depends on equilibrium composition, not only on starting stoichiometry. Changing temperature, pressure, composition, or product removal can alter that composition.\n\nChemical kinetics determines how quickly products form. A reaction may give a low yield at a specified time because it proceeds slowly, even if substantial product formation is thermodynamically favored.\n\nCatalysis can accelerate reactions and change competition between reaction pathways. A catalyst does not, by itself, change the equilibrium constant for a specified reaction at a fixed temperature.\n\nCompeting and consecutive reactions\n\nStarting materials may follow several pathways, producing different substances. The desired product may also react further:\n\n\\[A\\rightarrow P\\rightarrow D.\\]\n\nIn this sequence, allowing the reaction to continue can increase consumption of \\(A\\) while reducing the amount of \\(P\\). Understanding the reaction mechanism helps explain why reaction time, reagent concentration, or addition order affects yield.\n\nMixing, transport, and stability\n\nPoor mixing can create local differences in concentration or temperature. In multiphase reactions, transport between phases may limit the rate at which reactants meet. Such effects can become especially important when a process is transferred from laboratory to production scale.\n\nProducts may also decompose through heat, light, oxygen exposure, or contact with the reaction medium. A lower isolated yield may therefore reflect instability during processing rather than inefficient initial formation."
    },
    {
      "heading": "Overall yield in multistep synthesis",
      "text": "For a sequence of reactions, the overall yield is the product of the individual fractional yields, provided that the steps use consistent stoichiometric bases:\n\n\\[Y_{\\mathrm{overall}} = \\prod_{i=1}^{k}Y_i.\\]\n\nThree successive steps, each giving 80%, have an overall yield of\n\n\\[0.80^3=0.512,\\]\n\nor 51.2%. Even relatively high individual yields therefore compound into substantial material loss over a long sequence.\n\nIn a convergent synthesis, separate branches produce intermediates that are later combined. Overall-yield calculations must specify the starting material being used as the reference and account for the coupling stoichiometry. Simply multiplying every reported yield across all branches can be misleading."
    },
    {
      "heading": "Interpretation and limitations",
      "text": "An apparent yield above 100% usually indicates that the numerator and denominator are not comparable or that the measurement includes material other than the intended product. Possible causes include residual solvent, impurities, an incorrect molecular formula, or an inaccurate estimate of starting-material content. It does not mean that the reaction exceeded its correctly calculated stoichiometric maximum.\n\nMeasurement uncertainty affects both product quantification and the theoretical-yield calculation. Balance readings, reagent purity, solution concentration, sampling, and analytical calibration can all contribute. Differences between reported yields may therefore be insignificant unless experimental variability is known.\n\nYield alone is not a complete measure of process efficiency. A high-yielding process may still require large reagent excesses, extensive solvent use, demanding separations, or substantial energy input. Atom economy instead describes how much of the reactant mass is incorporated into the desired product according to the balanced equation; it is distinct from experimentally measured yield.\n\nFor meaningful comparison, a reported yield identifies the product and chemical form, the limiting reagent or other reference basis, whether the value is isolated or analytical, and any purity correction. Values calculated after subtracting recovered starting material must be distinguished from yields based on the full initial charge."
    }
  ],
  "links": [
    "chemical-reaction",
    "stoichiometry",
    "molar-mass",
    "chemical-equation",
    "mole",
    "organic-chemistry",
    "distillation",
    "chromatography",
    "solvent",
    "nuclear-magnetic-resonance",
    "spectroscopy",
    "calibration",
    "chemical-equilibrium",
    "temperature",
    "pressure",
    "chemical-kinetics",
    "catalysis",
    "reaction-mechanism",
    "measurement-uncertainty"
  ],
  "sources": [],
  "license": "https://creativecommons.org/licenses/by/4.0/"
}