{
  "id": "pascals-principle",
  "title": "Pascal’s Principle",
  "lang": "en",
  "source_lang": "en",
  "summary": "Pascal’s principle states that a pressure change applied to a confined fluid is transmitted undiminished throughout the fluid, providing the basis for hydraulic force transmission.",
  "category": "science",
  "subcategory": "physics",
  "type": "concept",
  "aliases": [
    "Pascal’s law",
    "principle of transmission of fluid pressure"
  ],
  "generated_at": "2026-11-03",
  "model": "pro/gpt-6.1-sol",
  "url": "https://aiwiki.page/en/pascals-principle/",
  "translations": {
    "zh-Hans": {
      "url": "https://aiwiki.page/zh/pascals-principle/",
      "json": "https://aiwiki.page/zh/pascals-principle.json"
    }
  },
  "sections": [
    {
      "heading": "",
      "text": "Pascal’s principle states that a change in pressure applied to a confined fluid at rest is transmitted undiminished throughout the fluid and to the walls of its container. Named after the French mathematician and physicist Blaise Pascal, it is a fundamental principle of hydrostatics and the basis of hydraulic presses, jacks, lifts, and braking systems. Its usual engineering formulation assumes a nearly incompressible liquid, a container that confines it, and conditions sufficiently close to equilibrium."
    },
    {
      "heading": "Physical meaning",
      "text": "Pressure is the normal force per unit area. For a uniform pressure acting on a flat surface,\n\n\\[p=\\frac{F_\\perp}{A},\\]\n\nwhere \\(F_\\perp\\) is the force perpendicular to the surface and \\(A\\) is its area. In the International System of Units, pressure is measured in pascals, with \\(1\\,\\mathrm{Pa}=1\\,\\mathrm{N\\,m^{-2}}\\).\n\nTwo closely related ideas are often presented under Pascal’s law:\n\n- Pressure at a point in a fluid at rest is the same in every direction. A stationary fluid cannot sustain a shear stress; its pressure acts normally on any surface.\n- An externally imposed pressure increase is transmitted throughout a confined fluid. In the ideal incompressible case, every point experiences the same additional pressure once equilibrium is established.\n\nThe second statement does not mean that pressure must have the same value everywhere. Under gravity, lower parts of a fluid generally have greater pressure than higher parts. Pascal’s principle concerns the change in pressure, not the removal of pre-existing differences.\n\nFor example, if a piston adds \\(50\\,\\mathrm{kPa}\\) to a confined liquid, the pressure at every point increases by \\(50\\,\\mathrm{kPa}\\) in the ideal model, even though pressures at different heights remain unequal."
    },
    {
      "heading": "Relation to hydrostatic equilibrium",
      "text": "For a fluid at rest in a uniform gravitational field, the vertical pressure gradient is\n\n\\[\\frac{dp}{dz}=-\\rho g,\\]\n\nwhere \\(z\\) increases upward, \\(\\rho\\) is the fluid’s density, and \\(g\\) is gravitational acceleration. For constant density,\n\n\\[p(z)=p(z_0)+\\rho g(z_0-z).\\]\n\nIf the pressure at the reference level \\(z_0\\) increases by \\(\\Delta p\\), while density and geometry remain unchanged, the new pressure is\n\n\\[p_{\\mathrm{new}}(z) = p(z_0)+\\Delta p+\\rho g(z_0-z).\\]\n\nConsequently,\n\n\\[p_{\\mathrm{new}}(z)-p(z)=\\Delta p\\]\n\nat every height. This directly expresses Pascal’s principle for a constant-density liquid.\n\nThe shape of the container does not appear in this result. A narrow connecting tube can therefore transmit pressure between much larger cylinders. Its size nevertheless affects how quickly liquid can flow and how much pressure is lost during motion."
    },
    {
      "heading": "Hydraulic force multiplication",
      "text": "A simple hydraulic press consists of two connected cylinders containing liquid, with pistons of areas \\(A_1\\) and \\(A_2\\). If the pistons are at the same height, external pressures are equal, and piston weight and friction are neglected, equilibrium gives\n\n\\[\\frac{F_1}{A_1}=\\frac{F_2}{A_2}.\\]\n\nThus,\n\n\\[F_2=F_1\\frac{A_2}{A_1}.\\]\n\nA larger output piston produces a larger output force because the same pressure acts over a larger area. The pressure itself is not multiplied.\n\nFor example, an input force of \\(100\\,\\mathrm{N}\\) applied to a piston of area \\(1\\,\\mathrm{cm^2}\\) creates an additional pressure of \\(1\\,\\mathrm{MPa}\\). Acting on an output piston of area \\(20\\,\\mathrm{cm^2}\\), that pressure produces an ideal output force of \\(2{,}000\\,\\mathrm{N}\\).\n\nIf the pistons are at different heights, a hydrostatic correction is required. For constant density,\n\n\\[p_2=p_1+\\rho g(z_1-z_2).\\]\n\nThe simple equal-pressure relation is therefore exact only when the relevant pressure surfaces are at the same elevation, or when the height correction is negligible.\n\nForce gain and displacement\n\nHydraulic force multiplication does not create energy. For an incompressible liquid with no leakage, conservation of mass requires equal displaced volumes:\n\n\\[A_1s_1=A_2s_2,\\]\n\nwhere \\(s_1\\) and \\(s_2\\) are the magnitudes of the piston displacements. Hence,\n\n\\[s_2=s_1\\frac{A_1}{A_2}.\\]\n\nCombining the force and displacement relations gives\n\n\\[F_1s_1=F_2s_2.\\]\n\nThe larger output force is accompanied by a proportionally smaller output displacement. In an ideal device, input and output work are equal. Real devices deliver less useful output work because of friction, fluid resistance, leakage, and deformation."
    },
    {
      "heading": "Applications",
      "text": "Presses, jacks, and lifts\n\nHydraulic presses use a large piston to apply substantial forces in metal forming, compression, and molding. Hydraulic jacks and vehicle lifts use the same pressure–area relation to raise loads.\n\nA practical jack commonly combines a small pumping piston with check valves. Repeated pump strokes transfer liquid into a larger lifting cylinder, allowing its total movement to exceed the displacement produced by a single stroke. The valves and reservoir make repeated operation possible; they are additional components rather than consequences of Pascal’s principle alone.\n\nHydraulic brakes\n\nIn a hydraulic braking system, a master cylinder creates pressure in brake fluid. This pressure is transmitted through connected lines to pistons at the wheels, where it produces forces that operate the brakes.\n\nThe resulting braking effect also depends on piston areas, mechanical leverage, and friction between braking surfaces. Equal hydraulic pressure does not necessarily imply equal braking force or equal braking torque at every wheel.\n\nIndustrial fluid-power systems\n\nHydraulic actuators are widely used in construction machinery, manufacturing equipment, and aircraft systems. Pumps supply fluid flow, while loads and control components determine the operating pressure. Pascal’s principle explains how pressure produces actuator force, but the behavior of a complete operating system also depends on flow resistance, valve characteristics, inertia, and fluid properties."
    },
    {
      "heading": "Assumptions and limitations",
      "text": "Compressibility\n\nLiquids are not perfectly incompressible. A pressure increase produces a small reduction in volume, characterized by the bulk modulus,\n\n\\[K=-V\\frac{dp}{dV}.\\]\n\nFor a small change,\n\n\\[\\frac{\\Delta V}{V}\\approx-\\frac{\\Delta p}{K}.\\]\n\nCompression stores energy and affects the displacement and response of hydraulic systems. Gas bubbles can greatly increase their effective compressibility.\n\nPressure transmission also occurs in confined gases, but gases usually undergo much larger volume and density changes. In a gravitational field, compression can alter the density distribution, so an exactly uniform additive pressure change throughout a tall gas column does not generally follow from the simple constant-density formulation.\n\nFinite transmission speed\n\nPressure changes are not transmitted instantaneously. They propagate as pressure disturbances at a finite speed determined by fluid compressibility and the elasticity of the container or pipe. Pascal’s principle describes the equilibrium or sufficiently slow-changing limit, not every stage of a rapid transient.\n\nSudden valve operation can generate water hammer, in which pressure varies strongly with position and time.\n\nFlow and viscous losses\n\nA flowing fluid generally requires pressure differences to overcome resistance. Viscosity, pipe geometry, fittings, and turbulence can therefore cause pressure drops between connected components. Equal static pressure at equal height is not a universal rule for a moving fluid.\n\nMechanical departures from the ideal model\n\nSeal friction, leakage, piston weight, flexible hoses, and cylinder deformation can all alter the relation between applied force and useful output. The basic piston equations describe forces due to fluid pressure; a complete force balance must include other forces acting on each piston."
    },
    {
      "heading": "Historical development",
      "text": "Pascal investigated fluid equilibrium and atmospheric pressure during the seventeenth century. His Treatise on the Equilibrium of Liquids, published posthumously in 1663, presented the principles underlying hydraulic force transmission, including the use of connected pistons of unequal areas.\n\nPractical development required cylinders and seals capable of containing high-pressure liquid. Joseph Bramah’s hydraulic press, patented in Britain in 1795, was an important step in turning the principle into an industrial technology. Later hydraulic machinery extended the same pressure–area relationship through improved pumps, valves, seals, and control systems."
    }
  ],
  "links": [
    "pressure",
    "blaise-pascal",
    "hydrostatics",
    "force",
    "international-system-of-units",
    "gravity",
    "density",
    "hydraulic-press",
    "energy",
    "conservation-of-mass",
    "work-physics",
    "friction",
    "viscosity",
    "turbulence"
  ],
  "sources": [],
  "license": "https://creativecommons.org/licenses/by/4.0/"
}