{
  "id": "partial-pressure",
  "title": "Partial Pressure",
  "lang": "en",
  "source_lang": "en",
  "summary": "Partial pressure expresses the contribution of an individual gas to a mixture’s total pressure and helps describe gas composition, equilibrium, and transport.",
  "category": "science",
  "subcategory": "physics",
  "type": "concept",
  "aliases": [
    "Component partial pressure"
  ],
  "generated_at": "2026-11-05",
  "model": "pro/gpt-6.1-sol",
  "url": "https://aiwiki.page/en/partial-pressure/",
  "translations": {
    "zh-Hans": {
      "url": "https://aiwiki.page/zh/partial-pressure/",
      "json": "https://aiwiki.page/zh/partial-pressure.json"
    }
  },
  "sections": [
    {
      "heading": "",
      "text": "Partial pressure is a pressure assigned to an individual component of a gas mixture. For an ideal gas mixture, it is the pressure that the component would exert if it alone occupied the mixture’s entire volume at the same temperature. More generally, the partial pressure of component \\(i\\) is defined as \\(p_i=y_iP\\), where \\(y_i\\) is its mole fraction in the gas phase and \\(P\\) is the total pressure. Partial pressures are central to describing atmospheric composition, gas–liquid equilibrium, chemical reactions, and respiratory gas exchange."
    },
    {
      "heading": "Definition and calculation",
      "text": "The mole fraction of a gas component is\n\n\\[y_i=\\frac{n_i}{n_{\\mathrm{tot}}},\\]\n\nwhere \\(n_i\\) is its amount of substance and \\(n_{\\mathrm{tot}}\\) is the total amount of gas. Its partial pressure is therefore\n\n\\[p_i=y_iP.\\]\n\nBecause the mole fractions sum to one,\n\n\\[\\sum_i p_i=P.\\]\n\nFor an ideal gas mixture, each component obeys\n\n\\[p_iV=n_iRT,\\]\n\nwhere \\(V\\) is the mixture’s volume, \\(R\\) is the gas constant, and \\(T\\) is absolute temperature. Combining this with the ideal-gas equation for the whole mixture gives the mole-fraction expression above.\n\nPartial pressure has the same units as total pressure. The SI unit is the pascal, although kilopascals, bars, atmospheres, and millimetres of mercury are also used.\n\nExample\n\nA mixture containing \\(2.0\\) moles of nitrogen and \\(1.0\\) mole of oxygen has a total pressure of \\(150\\ \\mathrm{kPa}\\). Its partial pressures are\n\n\\[p_{\\mathrm{N_2}}=\\frac{2}{3}(150)=100\\ \\mathrm{kPa},\\]\n\n\\[p_{\\mathrm{O_2}}=\\frac{1}{3}(150)=50\\ \\mathrm{kPa}.\\]\n\nThese are not pressures confined to separate regions of the vessel. Both gases occupy the entire available volume."
    },
    {
      "heading": "Dalton’s law and its molecular basis",
      "text": "Dalton’s law of partial pressures, formulated by John Dalton in the early nineteenth century, states that the total pressure of an ideal gas mixture equals the sum of the pressures its components would exert separately at the same temperature and volume.\n\nIn statistical mechanics, gas pressure arises from molecular momentum transfer to the container walls. For a classical ideal gas mixture,\n\n\\[p_i=\\frac{N_i k_{\\mathrm B}T}{V},\\]\n\nwhere \\(N_i\\) is the number of molecules of component \\(i\\) and \\(k_{\\mathrm B}\\) is the Boltzmann constant. Contributions from the different molecular species add because the ideal-gas model neglects intermolecular interactions.\n\nAt a fixed temperature, heavier molecules move more slowly on average than lighter molecules, but their greater mass compensates for this difference in the pressure expression. Equal numbers of ideal-gas molecules in the same volume therefore make equal pressure contributions, regardless of their chemical identity.\n\nFor real mixtures, \\(p_i=y_iP\\) remains a useful definition and its sum is still \\(P\\). What becomes approximate is the interpretation of \\(p_i\\) as the pressure the isolated component would exert in that same volume."
    },
    {
      "heading": "Relation to composition and concentration",
      "text": "Partial pressure depends on both composition and total pressure. A gas present at a fixed mole fraction has a lower partial pressure when the mixture’s total pressure falls and a higher partial pressure when it rises.\n\nFor example, oxygen makes up approximately \\(20.95\\%\\) of dry air. At a total pressure of \\(101.325\\ \\mathrm{kPa}\\), its partial pressure is approximately\n\n\\[p_{\\mathrm{O_2}}=0.2095(101.325)\\approx21.2\\ \\mathrm{kPa}.\\]\n\nIn the well-mixed lower atmosphere, the oxygen mole fraction remains approximately constant with altitude, while its partial pressure decreases as atmospheric pressure falls.\n\nFor an ideal mixture, partial pressure is related to molar concentration by\n\n\\[p_i=c_iRT,\\]\n\nwhere \\(c_i=n_i/V\\). Thus, equal partial pressures imply equal number concentrations only when the temperatures are also equal.\n\nFor ideal gases, a volume fraction determined at a common temperature and pressure equals the mole fraction. A mass fraction generally does not: converting mass composition to mole composition requires the components’ molar masses."
    },
    {
      "heading": "Water vapor and wet-gas corrections",
      "text": "A gas collected over water normally contains water vapor as well as the gas being collected. For an approximately ideal mixture,\n\n\\[P=p_{\\mathrm{dry\\ gas}}+p_{\\mathrm{H_2O}}.\\]\n\nIf the mixture is in equilibrium with pure liquid water, the water-vapor partial pressure is approximately the saturation vapor pressure of water at that temperature. The dry-gas pressure is then\n\n\\[p_{\\mathrm{dry\\ gas}}=P-p_{\\mathrm{H_2O}}.\\]\n\nSaturation must not be assumed merely because water vapor is present. In unsaturated air, its partial pressure is below the saturation value.\n\nRelative humidity is commonly approximated by\n\n\\[\\mathrm{RH}=100\\%\\frac{p_{\\mathrm{H_2O}}}{p_{\\mathrm{sat}}(T)}.\\]\n\nThis explains why relative humidity can change when air is heated or cooled even if its water-vapor content changes little: the saturation vapor pressure depends strongly on temperature.\n\nIf \\(y_{i,\\mathrm{dry}}\\) is a component’s mole fraction after excluding water vapor, its partial pressure in the humid mixture is approximately\n\n\\[p_i=y_{i,\\mathrm{dry}}\\left(P-p_{\\mathrm{H_2O}}\\right).\\]\n\nSpecifying whether a composition is reported on a wet or dry basis is therefore important."
    },
    {
      "heading": "Gas dissolution and phase equilibrium",
      "text": "Partial pressure helps determine the equilibrium amount of a gas dissolved in a liquid. In one common form of Henry’s law,\n\n\\[c_i=k_{\\mathrm H}p_i,\\]\n\nwhere \\(c_i\\) is the dissolved concentration and \\(k_{\\mathrm H}\\) is a temperature-dependent constant for the gas–solvent system. Other conventions define Henry’s constant differently, including by using the reciprocal relation, so its equation and units must be specified.\n\nHenry’s law describes a limiting dilute-solution relationship. Chemical reactions in the liquid, nonideal solution behavior, and elevated pressures can require additional treatment. For example, dissolved carbon dioxide participates in aqueous acid–base equilibria, so the total dissolved inorganic carbon is not determined by physical dissolution alone.\n\nA related distinction arises in liquid–vapor equilibrium. For an ideal liquid solution, Raoult’s law gives\n\n\\[p_i=x_i p_i^*(T),\\]\n\nwhere \\(x_i\\) is the liquid-phase mole fraction and \\(p_i^*(T)\\) is the pure component’s saturation vapor pressure. The liquid composition \\(x_i\\) is generally different from the gas composition \\(y_i\\). This difference is fundamental to distillation."
    },
    {
      "heading": "Chemical equilibrium and real gases",
      "text": "In gas-phase chemical equilibrium, partial pressures enter the activities of ideal gaseous reactants and products. For a reaction written as\n\n\\[\\sum_i \\nu_i A_i=0,\\]\n\nthe dimensionless pressure-based reaction quotient is\n\n\\[Q_p=\\prod_i\\left(\\frac{p_i}{p^\\circ}\\right)^{\\nu_i},\\]\n\nwhere \\(\\nu_i\\) is positive for products and negative for reactants, and \\(p^\\circ\\) is the standard pressure. At equilibrium, \\(Q_p\\) equals the corresponding equilibrium constant.\n\nThe connection to chemical potential is\n\n\\[\\mu_i=\\mu_i^\\circ(T)+RT\\ln\\left(\\frac{p_i}{p^\\circ}\\right)\\]\n\nfor an ideal gas mixture.\n\nFor a real gas mixture, partial pressure alone does not fully describe thermodynamic behavior. It is replaced in this expression by fugacity, \\(f_i\\):\n\n\\[\\mu_i=\\mu_i^\\circ(T)+RT\\ln\\left(\\frac{f_i}{p^\\circ}\\right), \\qquad f_i=\\phi_i y_iP.\\]\n\nHere \\(\\phi_i\\) is the component’s fugacity coefficient in the mixture. In the ideal-gas limit, \\(\\phi_i\\) approaches one and fugacity approaches partial pressure. Departures become important particularly at high pressures and near condensation."
    },
    {
      "heading": "Gas transport, physiology, and measurement",
      "text": "Partial-pressure differences are widely used to describe gas exchange across interfaces. Under suitable dilute or ideal conditions, they correspond to concentration differences that drive diffusion. More generally, transport is governed by chemical-potential gradients rather than by total pressure alone. Two mixtures can have identical total pressures but exchange individual gases because their compositions differ.\n\nIn respiratory physiology, oxygen and carbon dioxide partial pressures describe gas exchange among air, blood, and tissues. A dissolved gas’s partial pressure is understood through the gas-phase pressure with which it would be in equilibrium. It is not the total mechanical pressure of the liquid.\n\nOxygen partial pressure is also distinct from total blood oxygen content. Much of the oxygen in blood is bound to hemoglobin, whereas oxygen partial pressure reflects dissolved oxygen. Binding allows oxygen content to change without a directly proportional change in partial pressure.\n\nIn laboratory and industrial work, partial pressures are often calculated from a measured total pressure and a measured mole fraction. Composition may be determined by chromatography, spectroscopy, or mass spectrometry. Reliable interpretation requires attention to temperature, humidity, instrument calibration, and whether the reported composition uses a wet or dry basis."
    }
  ],
  "links": [
    "ideal-gas",
    "pressure",
    "temperature",
    "mole-fraction",
    "amount-of-substance",
    "gas-constant",
    "international-system-of-units",
    "nitrogen",
    "oxygen",
    "daltons-law",
    "statistical-mechanics",
    "boltzmann-constant",
    "atmosphere-of-earth",
    "molar-concentration",
    "molar-mass",
    "water",
    "vapor-pressure",
    "relative-humidity",
    "henrys-law",
    "carbon-dioxide",
    "raoults-law",
    "distillation",
    "chemical-equilibrium",
    "reaction-quotient",
    "equilibrium-constant",
    "chemical-potential",
    "fugacity",
    "diffusion",
    "hemoglobin",
    "mass-spectrometry"
  ],
  "sources": [],
  "license": "https://creativecommons.org/licenses/by/4.0/"
}