{
  "id": "newtonian-fluid",
  "title": "Newtonian Fluid",
  "lang": "en",
  "source_lang": "en",
  "summary": "A Newtonian fluid has viscous stresses that depend linearly on its instantaneous rate of deformation, with viscosities independent of that rate at fixed thermodynamic conditions.",
  "category": "science",
  "subcategory": "physics",
  "type": "concept",
  "aliases": [
    "Newtonian liquid",
    "Newtonian viscous fluid"
  ],
  "generated_at": "2026-11-04",
  "model": "pro/gpt-6.1-sol",
  "url": "https://aiwiki.page/en/newtonian-fluid/",
  "translations": {
    "zh-Hans": {
      "url": "https://aiwiki.page/zh/newtonian-fluid/",
      "json": "https://aiwiki.page/zh/newtonian-fluid.json"
    }
  },
  "sections": [
    {
      "heading": "",
      "text": "A Newtonian fluid is a fluid whose viscous stress is a linear function of its instantaneous rate of deformation. In simple shear, this means that shear stress is proportional to shear rate, with dynamic viscosity as the proportionality coefficient. At fixed temperature, pressure, and composition, that coefficient does not depend on the shear rate or the history of deformation. Many ordinary liquids and gases, including water and air under common conditions, are well described by this model. The term refers to a material’s stress–deformation relation, not to whether its flow is slow, steady, or turbulent."
    },
    {
      "heading": "Newton’s law of viscosity",
      "text": "Consider a fluid moving in parallel layers, with velocity \\(u\\) in the \\(x\\)-direction varying with the perpendicular coordinate \\(y\\). Its shear rate is\n\n\\[\\dot{\\gamma}=\\frac{\\mathrm{d}u}{\\mathrm{d}y}.\\]\n\nFor a Newtonian fluid, the corresponding shear-stress component is\n\n\\[\\tau_{xy}=\\mu\\dot{\\gamma},\\]\n\nwhere \\(\\mu\\) is the dynamic viscosity. This expression uses a stress-component convention; the force exerted by a fluid on a moving surface opposes the surface’s relative motion.\n\nShear stress is tangential force per unit area. In the International System of Units, it is measured in pascals, shear rate in reciprocal seconds, and dynamic viscosity in pascal-seconds. A positive viscosity represents resistance to relative motion between adjacent fluid layers.\n\nA plot of shear stress against shear rate is therefore a straight line through the origin, with slope \\(\\mu\\). There is no finite yield stress that must be exceeded before steady shearing begins.\n\nFor an idealized fluid layer between parallel plates separated by distance \\(h\\), with one plate stationary and the other moving at speed \\(U\\), steady flow with no pressure gradient and no slipping at the walls gives\n\n\\[u(y)=\\frac{U}{h}y, \\qquad \\tau_{xy}=\\mu\\frac{U}{h}.\\]\n\nThus, doubling the plate speed doubles the shear stress if viscosity and plate spacing remain unchanged.\n\nThe name honors Isaac Newton, who described resistance associated with the relative motion of fluid layers in his 1687 Principia. The modern three-dimensional formulation developed subsequently within continuum mechanics."
    },
    {
      "heading": "General constitutive equation",
      "text": "The simple-shear law is one special case of a three-dimensional constitutive equation: a relation specifying how a material responds to deformation.\n\nFor an isotropic Newtonian fluid, the total stress tensor can be written as\n\n\\[\\boldsymbol{\\sigma} = -p\\mathbf{I} + 2\\mu\\mathbf{D} + \\lambda(\\nabla\\cdot\\mathbf{u})\\mathbf{I},\\]\n\nwhere:\n\n- \\(\\boldsymbol{\\sigma}\\) is the Cauchy stress tensor;\n- \\(p\\) is thermodynamic pressure;\n- \\(\\mathbf{I}\\) is the identity tensor;\n- \\(\\mathbf{u}\\) is the velocity field;\n- \\(\\mu\\) is the shear viscosity;\n- \\(\\lambda\\) is the second viscosity coefficient;\n- \\(\\mathbf{D}\\) is the rate-of-deformation tensor,\n\n\\[\\mathbf{D} = \\frac{1}{2} \\left[ \\nabla\\mathbf{u}+(\\nabla\\mathbf{u})^{\\mathsf T} \\right].\\]\n\nOnly the symmetric part of the velocity gradient enters the viscous stress. A rigid rotation alone does not deform a fluid element and therefore does not produce viscous stress in this model.\n\nAn equivalent form separates shape change from volume change:\n\n\\[\\boldsymbol{\\sigma} = -p\\mathbf{I} + 2\\mu \\left[ \\mathbf{D} -\\frac{1}{3}(\\nabla\\cdot\\mathbf{u})\\mathbf{I} \\right] + \\zeta(\\nabla\\cdot\\mathbf{u})\\mathbf{I},\\]\n\nwhere \\(\\zeta=\\lambda+2\\mu/3\\) is the bulk viscosity. Shear viscosity describes resistance to changes of shape, while bulk viscosity describes the dissipative stress associated with volumetric expansion or compression.\n\nFor incompressible flow,\n\n\\[\\nabla\\cdot\\mathbf{u}=0,\\]\n\nso the relation reduces to\n\n\\[\\boldsymbol{\\sigma}=-p\\mathbf{I}+2\\mu\\mathbf{D}.\\]\n\nIn this incompressible formulation, pressure acts as a constraint enforcing volume conservation rather than being determined solely by an equation of state.\n\nThe sometimes-used Stokes hypothesis, \\(\\lambda=-2\\mu/3\\), sets bulk viscosity to zero. It is an additional modeling assumption, not part of the definition of a Newtonian fluid."
    },
    {
      "heading": "Physical interpretation and material properties",
      "text": "Viscosity reflects microscopic transfer of momentum. In dilute gases, molecules carry momentum between regions moving at different average velocities. In liquids, intermolecular interactions and molecular rearrangements also play important roles.\n\nNewtonian behavior is a macroscopic approximation applicable when microscopic relaxation is rapid compared with the timescale of the imposed deformation. The model has no independent memory of earlier deformation and no elastic shear response.\n\nA Newtonian fluid need not have a viscosity that is constant under all circumstances. Its viscosity may depend on temperature, pressure, and composition:\n\n\\[\\mu=\\mu(T,p,\\text{composition}).\\]\n\nThe defining restriction is that, at a given local thermodynamic state, viscosity does not depend on the rate or history of deformation. Consequently, heating during an experiment can produce an apparent change of viscosity with shear rate even when the underlying constitutive behavior is Newtonian.\n\nFor many liquids, viscosity decreases as temperature rises. For dilute gases, viscosity generally increases with temperature over ordinary operating ranges. These trends arise from different microscopic transport mechanisms and do not determine whether a fluid is Newtonian.\n\nKinematic viscosity is defined by\n\n\\[\\nu=\\frac{\\mu}{\\rho},\\]\n\nwhere \\(\\rho\\) is density. It has units of square metres per second and is useful in describing momentum diffusion."
    },
    {
      "heading": "Examples and departures from Newtonian behavior",
      "text": "Water, many simple organic liquids, and ordinary gases are approximately Newtonian across broad practical ranges of deformation rate. Some oils are also approximately Newtonian, although additives, suspended material, and operating conditions can change their behavior.\n\nA non-Newtonian fluid does not follow the Newtonian constitutive relation over the conditions considered. Common departures include:\n\n- Shear thinning: apparent viscosity decreases as shear rate increases.\n- Shear thickening: apparent viscosity increases as shear rate increases.\n- Yield-stress behavior: sustained flow occurs only after an applied stress exceeds a threshold in an idealized material model.\n- Time-dependent response: stress depends on deformation history as well as the current deformation rate.\n- Viscoelasticity: the material exhibits both viscous dissipation and an elastic response.\n\nConcentrated suspensions, polymer solutions, pastes, and emulsions frequently exhibit such behavior. Material names alone are not sufficient for classification: concentration, temperature, deformation rate, and observation timescale can all matter.\n\nA constant shear viscosity measured over a limited range is not by itself proof of fully Newtonian behavior. Some materials have a nearly constant shear viscosity yet exhibit elastic normal stresses or non-Newtonian behavior in extension. For an incompressible isotropic Newtonian fluid in uniaxial extension, the extensional viscosity is \\(3\\mu\\), a relation known as the Trouton ratio."
    },
    {
      "heading": "Governing equations and flow regimes",
      "text": "Combining the Newtonian constitutive relation with conservation of mass and momentum balance gives the Navier–Stokes equations. For an incompressible fluid with constant viscosity,\n\n\\[\\rho \\left( \\frac{\\partial\\mathbf{u}}{\\partial t} + \\mathbf{u}\\cdot\\nabla\\mathbf{u} \\right) = -\\nabla p + \\mu\\nabla^2\\mathbf{u} + \\rho\\mathbf{b},\\]\n\nwhere \\(\\mathbf{b}\\) is body force per unit mass, such as gravitational acceleration.\n\nThe Newtonian constitutive law is linear in deformation rate, but the resulting flow equations are generally nonlinear because of the advective term \\(\\mathbf{u}\\cdot\\nabla\\mathbf{u}\\). Newtonian fluids can therefore display complex behavior, including turbulence.\n\nThe Reynolds number,\n\n\\[\\mathrm{Re}=\\frac{\\rho U L}{\\mu},\\]\n\ncompares inertial and viscous effects using characteristic velocity \\(U\\) and length \\(L\\). Whether a flow is laminar or turbulent depends on this balance, the geometry, and disturbances—not simply on whether the fluid is Newtonian.\n\nFor steady, fully developed laminar flow of an incompressible Newtonian fluid through a straight circular pipe, with constant viscosity and no wall slip, the volume flow rate is\n\n\\[Q=\\frac{\\pi R^4}{8\\mu L}\\Delta p,\\]\n\nwhere \\(R\\) is pipe radius, \\(L\\) is pipe length, and \\(\\Delta p\\) is the pressure drop. This is the Hagen–Poiseuille law. Its linear pressure–flow relation does not generally apply to turbulent pipe flow."
    },
    {
      "heading": "Measurement, applications, and limitations",
      "text": "Newtonian behavior is investigated through rheology, the study of deformation and flow. Rotational instruments measure stress and shear rate in controlled geometries, while capillary methods infer viscosity from pressure-driven flow. Measurements across multiple deformation rates help establish whether viscosity remains constant within experimental uncertainty.\n\nInterpretation must account for temperature changes, wall slip, instrument inertia, and secondary flows. These can produce apparent rate dependence unrelated to the material’s constitutive behavior.\n\nThe Newtonian model underlies much of hydraulics, lubrication theory, aerodynamics, and computational fluid dynamics. It is especially useful because it describes many common fluids with relatively few material parameters.\n\nIts validity nevertheless has limits. Strong deformation, very short observation times, molecular confinement, complex internal structure, or rarefied-gas conditions may require other models. In particular, the continuum assumption can fail when the relevant flow length scale approaches molecular scales or the molecular mean free path. Newtonian behavior is therefore a constitutive approximation valid over a specified range of conditions, rather than an unrestricted property inferred solely from a substance’s identity."
    }
  ],
  "links": [
    "viscosity",
    "temperature",
    "pressure",
    "water",
    "force",
    "international-system-of-units",
    "isaac-newton",
    "equation-of-state",
    "momentum",
    "density",
    "non-newtonian-fluid",
    "conservation-of-mass",
    "navier-stokes-equations",
    "gravity",
    "turbulence",
    "reynolds-number",
    "rheology"
  ],
  "sources": [],
  "license": "https://creativecommons.org/licenses/by/4.0/"
}