{
  "id": "hall-effect",
  "title": "Hall Effect",
  "lang": "en",
  "source_lang": "en",
  "summary": "The Hall effect is a transverse electrical response used to measure magnetic fields and investigate charge carriers, electronic structure, and quantum states.",
  "category": "science",
  "subcategory": "physics",
  "type": "concept",
  "aliases": [
    "Hall phenomenon"
  ],
  "generated_at": "2026-11-03",
  "model": "pro/gpt-6.1-sol",
  "url": "https://aiwiki.page/en/hall-effect/",
  "translations": {
    "zh-Hans": {
      "url": "https://aiwiki.page/zh/hall-effect/",
      "json": "https://aiwiki.page/zh/hall-effect.json"
    }
  },
  "sections": [
    {
      "heading": "",
      "text": "The Hall effect is the appearance of a transverse voltage in a material carrying an electric current when a magnetic field acts perpendicular to the current. In its ordinary form, the field deflects moving charge carriers sideways until an opposing electric field develops. The resulting Hall voltage provides information about the sign, concentration, and motion of the carriers. Related transverse responses, arising from magnetism, quantum structure, or spin-dependent motion, form a broader family of Hall effects.\n\nDiscovered by Edwin Herbert Hall in 1879, the effect became a fundamental tool of condensed-matter physics and a practical basis for magnetic sensors. It helps distinguish electron-like from hole-like conduction, characterize semiconductors, measure electrical currents without direct electrical contact, and investigate magnetic materials. Under particular conditions, the Hall response becomes quantized, connecting electrical measurements to fundamental constants and the topology of electronic states.\n\nThe simplest description treats the carriers as classical charged particles. Real materials require a richer account involving electronic band structure, collisions, multiple carrier populations, and sometimes strongly correlated quantum states. These distinctions determine when a Hall measurement yields a straightforward carrier density and when it instead probes more complex collective or geometric properties."
    },
    {
      "heading": "Discovery and historical development",
      "text": "Edwin Herbert Hall discovered the effect in 1879 while working as a graduate student at Johns Hopkins University under Henry Augustus Rowland. The experiment addressed a question about how a magnetic field acts on a current-carrying conductor: whether its action could be understood only as a mechanical force on the conductor or whether it also altered the distribution of electricity within it. Hall passed a current through a thin gold strip and applied a magnetic field perpendicular to its surface. Contacts on opposite sides of the strip detected a small transverse voltage.\n\nUsing a thin sample was crucial because the Hall voltage, for a fixed total current and magnetic field, increases as the sample thickness decreases. In ordinary metals, the large concentration of mobile carriers makes the effect small. Thin metal foil therefore made the signal accessible to the sensitive electrical instruments of the period. Reversing the current or magnetic field reversed the transverse signal, helping identify it as a genuine field-dependent effect rather than a static imbalance between the contacts.\n\nHall’s discovery preceded identification of the electron as a particle in 1897. It supplied evidence that electrical conduction involved mobile charge whose motion could be deflected within matter. It did not, however, immediately establish a universally simple microscopic account of metallic conduction. Some metals exhibited a Hall sign inconsistent with the later elementary picture of freely moving negative electrons. This apparent difficulty became understandable only with the development of band theory and the concept of an electron hole.\n\nIn 1881 Hall also reported an enhanced transverse response in ferromagnetic materials. This became known as the anomalous Hall effect, distinguished from the ordinary response because it depends on magnetic order and relativistic properties of the electrons. The distinction remained important throughout the twentieth century: the ordinary effect became a standard probe of carrier transport, whereas the anomalous effect required an account of magnetism, scattering, and electronic wave functions.\n\nPaul Drude’s electron theory of metals, introduced in 1900, supplied a simple quantitative explanation of the ordinary effect. Later quantum mechanics explained why real solids often depart from that model. Semiconductor technology subsequently made Hall measurements and Hall sensors widespread, while the discoveries of the integer quantum Hall effect in 1980 and the fractional quantum Hall effect in 1982 transformed transverse transport into a major subject of fundamental physics."
    },
    {
      "heading": "Classical mechanism and defining equations",
      "text": "Consider a rectangular conductor with current along the \\(x\\)-direction, width \\(w\\) along \\(y\\), and thickness \\(t\\) along \\(z\\). A magnetic field \\(B_z\\) is applied perpendicular to the broad face. A carrier with charge \\(q\\) and drift velocity \\(\\mathbf v\\) experiences the Lorentz force\n\n\\[\\mathbf F=q(\\mathbf E+\\mathbf v\\times\\mathbf B).\\]\n\nThe magnetic part pushes carriers toward one side. Their redistribution produces a transverse electric field, which grows until there is no net transverse current in the steady state.\n\nFor a single carrier population with number density \\(n\\), the current density is \\(j_x=nqv_x\\). With the stated axes, transverse force balance gives \\(E_y=v_xB_z\\). The Hall coefficient is therefore\n\n\\[R_H=\\frac{E_y}{j_xB_z}=\\frac{1}{nq}.\\]\n\nFor electrons, \\(q=-e\\), where \\(e\\) is the positive elementary charge, so the simple model gives a negative coefficient. For positively charged carriers it gives a positive coefficient. The coefficient has SI units of cubic metres per coulomb. Its sign must always be interpreted together with the stated field, current, and voltage conventions.\n\nIf the oriented Hall voltage is defined as \\(V_H=E_yw\\), and \\(I=j_xwt\\), then\n\n\\[V_H=R_H\\frac{IB_z}{t}.\\]\n\nHere \\(V_H\\) is the voltage drop along the positive \\(y\\)-direction; reversing the voltmeter leads reverses its reported sign. The formula shows why thin samples, stronger magnetic fields, and larger currents increase the signal. For example, an ideal electron conductor with \\(n=10^{22}\\,\\mathrm{m^{-3}}\\), thickness \\(100\\,\\mu\\mathrm m\\), current \\(1\\,\\mathrm{mA}\\), and field \\(0.1\\,\\mathrm T\\) has a Hall-voltage magnitude of approximately \\(0.624\\,\\mathrm{mV}\\). This estimate assumes uniform current flow and negligible geometric corrections.\n\nIn the Drude model, collisions are represented by a relaxation time \\(\\tau\\). The carrier mobility is \\(\\mu=|q|\\tau/m^\\ast\\), where \\(m^\\ast\\) is an effective mass, and the zero-field conductivity is \\(\\sigma_0=n|q|\\mu\\). Although \\(\\tau\\) controls longitudinal conduction, it cancels from the elementary expression for \\(R_H\\). The magnitude of the Hall angle, describing the angular relation between the current and electric field, satisfies\n\n\\[|\\tan\\theta_H|=\\mu|B_z|\\]\n\nin this ideal model.\n\nThe magnetic force does not directly do work on the carriers because it is perpendicular to their velocity. The Hall field is likewise perpendicular to the net current in the ideal open-circuit transverse geometry. Dissipation instead arises from the longitudinal field and collisions. This distinction is essential when Hall transport is compared with Joule heating or with the nearly dissipationless transport found in quantum Hall states."
    },
    {
      "heading": "Carrier density, band structure, and departures from the simple model",
      "text": "The relation \\(R_H=1/(nq)\\) is exact only within restricted transport models. In a crystalline solid, electrons occupy energy bands rather than moving as free particles in empty space. Their velocities and response to forces depend on the variation of energy with crystal momentum. Consequently, the Hall response can reflect the shape of the Fermi surface, the distribution of scattering rates, and the presence of several conducting bands.\n\nAn almost filled band provides a particularly important example. Its electrical response can often be described more simply in terms of the few missing electrons, or holes, than in terms of all the occupied states. Holes respond as positively charged mobile carriers even though the underlying particles are electrons. This accounts for positive Hall coefficients in many materials without implying that their current is carried by free positive particles moving between atoms. In complicated metals, however, assigning one carrier sign to the entire material can be misleading.\n\nIn a semiconductor containing both electrons and holes, their contributions are weighted differently in longitudinal and transverse transport. For an isotropic two-carrier model in the weak-field limit,\n\n\\[R_H= \\frac{p\\mu_h^2-n\\mu_e^2} {e(p\\mu_h+n\\mu_e)^2},\\]\n\nwhere \\(n\\) and \\(p\\) are electron and hole concentrations, and \\(\\mu_e\\) and \\(\\mu_h\\) are their positive mobilities. The squared mobilities in the numerator mean that a relatively small population of highly mobile carriers can determine the Hall sign. A positive coefficient therefore does not necessarily mean that holes outnumber electrons.\n\nFor a single dominant carrier type, semiconductor measurements are often expressed as\n\n\\[R_H=\\frac{r_H}{nq},\\]\n\nwhere \\(r_H\\) is the Hall factor. It accounts for effects such as the energy dependence of scattering and, depending on the model, band anisotropy. The Hall density, \\(n_H=1/(e|R_H|)\\), is thus an experimentally defined quantity that need not equal the actual carrier density. Similarly, the Hall mobility,\n\n\\[\\mu_H=|R_H|\\sigma,\\]\n\ncan differ from the drift mobility. These distinctions matter when comparing samples at different temperatures or interpreting a change in the dominant scattering mechanism.\n\nMagnetic-field dependence supplies additional information. In a simple one-carrier conductor the transverse resistivity is linear in field. Multiple carrier populations can produce curvature because each population responds according to its own mobility. Measurements of both transverse resistivity and longitudinal magnetoresistance can constrain a multiband model, but the inferred parameters may not be unique over a limited field range. High-field behavior can simplify some models, yet does not provide a universal carrier-counting rule for arbitrary band structures.\n\nHall measurements are consequently strongest when combined with independent information. Optical measurements, quantum oscillations, chemical composition, and controlled electrostatic gating can help distinguish changes in carrier number from changes in mobility or band occupancy. A Hall-sign reversal may mark a change in dominant conduction, but it can also result from temperature-dependent scattering without any change in the underlying carrier types."
    },
    {
      "heading": "Experimental geometries and measurement accuracy",
      "text": "A conventional Hall measurement uses separate contacts for current injection and voltage detection. In a Hall-bar geometry, current flows along an elongated sample while transverse voltage probes connect to opposite sides. Additional longitudinal probes measure the resistive voltage drop along the current direction. This arrangement separates the Hall response from ordinary electrical resistance and allows both components of the transport tensor to be studied.\n\nPerfect contact placement is difficult. A small longitudinal displacement between transverse probes introduces part of the much larger longitudinal voltage into the measured signal. For a nonmagnetic sample in an ordinary Hall measurement, this contamination is commonly suppressed by antisymmetrizing in magnetic field:\n\n\\[V_{xy}^{\\mathrm{odd}}(B) = \\frac{V_{xy}(B)-V_{xy}(-B)}{2}.\\]\n\nThe ordinary Hall contribution reverses sign with field, whereas the usual longitudinal magnetoresistive contribution is even in field. Current reversal can additionally remove offsets that do not reverse with current, including many thermoelectric voltages. These procedures require greater care in magnetic materials because reversing the field can also change the magnetic domain state.\n\nThe van der Pauw method, introduced by Leo van der Pauw in 1958, extends transport measurements to thin samples of many shapes. Its standard formulation assumes a homogeneous, isotropic sample of uniform thickness, without holes, and with sufficiently small contacts on its perimeter. Different current and voltage configurations yield the sheet resistance; measurements in perpendicular magnetic fields determine the Hall response. The method is especially useful for semiconductor wafers and films that are not patterned into long Hall bars.\n\nThickness enters directly when converting a measured transverse resistance into a three-dimensional Hall coefficient. In a two-dimensional conducting layer, the natural quantity is instead the sheet carrier density \\(n_s\\), measured per unit area. For one electron-like carrier population,\n\n\\[\\frac{V_H}{I}=-\\frac{B}{n_se}.\\]\n\nAn uncertain conducting thickness can therefore be avoided by reporting sheet quantities, although converting them to a volume density still requires a justified thickness. This distinction is important in surface accumulation layers, semiconductor heterostructures, and atomically thin materials.\n\nMeasurement uncertainty also arises from magnetic-field calibration, finite contact size, current spreading, leakage, sample inhomogeneity, and heating. Excess current can raise the carrier temperature or alter carrier populations. Temperature gradients may create transverse thermoelectric signals. Alternating-current excitation and phase-sensitive detection can improve sensitivity, but parasitic capacitance and phase shifts must be controlled.\n\nNot every transverse voltage is an ordinary Hall voltage. Magnetic anisotropy can generate a planar transverse response, and thermal gradients can produce a Nernst signal. In unusual crystals, longitudinal transport itself may have field-antisymmetric components under particular experimental conditions. Reliable interpretation therefore depends on sample symmetry, contact geometry, current and field reversal tests, and an appropriate model of the material rather than on antisymmetrization alone."
    },
    {
      "heading": "Hall sensors and engineering applications",
      "text": "A Hall sensor converts magnetic-field information into an electrical signal. Its active element is commonly a semiconductor region supplied with a controlled current or voltage, with contacts arranged to detect the transverse response. Integrated circuitry amplifies the signal and may compensate for temperature drift and offset. Depending on the design, the output is a continuous voltage, a digital field measurement, or a switching signal indicating that a threshold has been crossed.\n\nFor an ideal current-driven plate, the current-related sensitivity is\n\n\\[S_I=\\frac{V_H}{IB}=\\frac{R_H}{t}.\\]\n\nA large Hall coefficient and a thin active region increase sensitivity. Material choice nevertheless involves trade-offs among mobility, resistance, noise, power consumption, processing compatibility, and stability. Silicon is especially important because Hall elements can be integrated with signal-processing electronics. Indium antimonide and indium arsenide are also useful Hall materials because of their high carrier mobilities, although practical performance depends on the complete device architecture rather than on mobility alone.\n\nHall sensors measure position and motion by detecting the field of a nearby permanent magnet. Applications include rotor-position detection in brushless motors, wheel-speed sensing, contactless switches, and angular encoders. A linear sensor follows the field continuously, whereas a Hall switch changes output at a specified threshold. A latch uses separate operating and release conditions, often associated with opposite field polarities. Hysteresis in the switching circuit prevents repeated transitions when the field fluctuates near a threshold.\n\nElectrical current can be measured indirectly through the magnetic field that it generates. In a Hall-based current transducer, a conductor may pass through a magnetic core that concentrates flux into a gap containing the sensor. Open-loop instruments infer current from the measured field. Closed-loop instruments use feedback to drive a compensating winding that approximately cancels the flux; the compensating current then provides the measurement. Unlike a simple inductive transformer, a Hall transducer can respond to direct current as well as time-varying current, within its bandwidth.\n\nSmall offsets are a major engineering problem because fabrication asymmetry and mechanical stress can produce voltages resembling the wanted signal. The spinning-current technique periodically exchanges the roles of the sensor’s contacts, allowing combinations of measurements to suppress substantial offset components. Chopper amplification, differential arrangements, and temperature compensation further improve performance. Remaining limitations include thermal and low-frequency noise, field nonuniformity, package stress, and changes in sensitivity with temperature.\n\nHall devices respond to the field component selected by their geometry, not directly to distance, angle, or current. Those quantities are inferred from a calibrated relationship between the source and the measured field. Three-axis devices combine differently oriented sensing elements to reconstruct a magnetic-field vector. Their accuracy depends on alignment, cross-axis sensitivity, surrounding magnetic materials, and calibration, in addition to the intrinsic properties of the Hall element."
    },
    {
      "heading": "Anomalous, planar, and texture-related Hall responses",
      "text": "In many magnetically ordered conductors, the transverse electrical response contains a component beyond the ordinary field-dependent Hall effect. A frequently used phenomenological expression for a ferromagnet is\n\n\\[\\rho_{yx}=R_0B_z+\\rho_{yx}^{A},\\]\n\nwith the anomalous term often approximated over a restricted regime as\n\n\\[\\rho_{yx}^{A}=R_s\\mu_0M_z.\\]\n\nHere \\(R_0\\) describes the ordinary contribution, \\(M_z\\) is the perpendicular magnetization, and \\(R_s\\) is an empirical anomalous Hall coefficient. This separation is useful but not universal: the anomalous response can depend on electronic structure and magnetic configuration in ways not captured by a single proportionality to magnetization.\n\nThree mechanisms are central to the anomalous Hall effect. Skew scattering is an asymmetry in the scattering probability caused by the combination of magnetic order and spin–orbit coupling. Side jump involves a transverse coordinate displacement associated with scattering. The intrinsic mechanism arises from the geometry of occupied electronic states and can exist without impurity scattering being its direct cause. Their relative importance depends on disorder, conductivity, band structure, and temperature.\n\nRobert Karplus and Joaquin Luttinger developed an intrinsic account in 1954. Modern formulations express this contribution using Berry curvature, a property of how quantum states change with crystal momentum. Berry curvature modifies the semiclassical velocity of a wave packet, adding a transverse term under an electric field. It provides a connection between anomalous Hall transport and the geometry of electronic wave functions.\n\nA nonzero net magnetic moment is not the sole criterion for an anomalous Hall effect. Some noncollinear antiferromagnets permit an intrinsic transverse charge response even though their net magnetization is small. The decisive restrictions arise from symmetry: relevant combinations of time-reversal and spatial symmetries can force the Hall response to vanish, while other magnetic arrangements allow it. Conversely, magnetic order alone does not guarantee a measurable anomalous Hall signal.\n\nThe planar Hall effect is physically distinct. In its conventional form, it results from anisotropic magnetoresistance when the magnetization lies at an angle to the current. The transverse resistivity is proportional to\n\n\\[(\\rho_\\parallel-\\rho_\\perp)\\sin\\theta\\cos\\theta,\\]\n\nwhere \\(\\rho_\\parallel\\) and \\(\\rho_\\perp\\) are resistivities for current parallel and perpendicular to the magnetization. Despite its name, this is a symmetric anisotropic resistive response rather than the ordinary antisymmetric Hall response.\n\nNoncoplanar magnetic textures can produce another transverse contribution, often called the topological Hall effect. Under suitable conditions, electrons moving through a smoothly varying spin texture acquire a geometric phase that acts like an effective magnetic field. Magnetic skyrmions are a prominent setting. Identifying such a contribution experimentally is not straightforward: multiband ordinary transport, magnetic inhomogeneity, or superposed anomalous signals can also generate extra structure in a Hall curve. Independent evidence about the magnetic texture is therefore important."
    },
    {
      "heading": "Integer, fractional, and anomalous quantum Hall effects",
      "text": "The quantum Hall effect occurs in effectively two-dimensional electronic systems and differs fundamentally from the continuously varying classical response. In the integer effect, the magnitude of the Hall resistance forms plateaus at\n\n\\[|R_{xy}|=\\frac{h}{\\nu e^2},\\]\n\nwhere \\(h\\) is the Planck constant and \\(\\nu\\) is an integer. Over a well-developed plateau, the longitudinal resistance becomes very small. Klaus von Klitzing discovered this behavior in 1980 in a silicon metal–oxide–semiconductor structure at low temperature and strong magnetic field.\n\nA perpendicular field organizes the orbital motion of two-dimensional electrons into Landau levels. Each level contains a large number of states, with a degeneracy per unit area of \\(e|B|/h\\) for each resolved internal component. The filling factor is\n\n\\[\\nu=\\frac{n_sh}{e|B|}.\\]\n\nDisorder localizes many bulk states between the extended states associated with successive levels. This allows the carrier density or field to vary over a finite range without changing the quantized Hall conductance, producing plateaus rather than isolated quantized points.\n\nThe same transport can be understood through conducting boundary channels. In an integer quantum Hall state, the bulk is insulating at the relevant chemical potential while edge states carry current in a directed manner. The number of channels is related to an integer topological invariant, the Chern number. Quantization is consequently robust against many microscopic imperfections, provided the conditions supporting the state and the measurement geometry remain intact.\n\nHorst Störmer, Daniel Tsui, and Arthur Gossard discovered the fractional quantum Hall effect in 1982 in a high-quality gallium arsenide heterostructure. A prominent state occurs at \\(\\nu=1/3\\), but many other rational filling factors are possible. Electron–electron interactions are essential: the electrons form correlated states that cannot generally be described as independently filling ordinary single-particle levels. Robert Laughlin’s 1983 wave-function construction explained a major class of these states and their fractionally charged excitations. Some fractional states are candidates for more unusual quasiparticle exchange statistics, whose experimental identification requires evidence beyond a resistance plateau alone.\n\nQuantized Hall resistance also underpins metrology. The von Klitzing constant is\n\n\\[R_K=\\frac{h}{e^2}\\approx25\\,812.80745\\,\\Omega.\\]\n\nSince the 2019 revision of the International System of Units, both \\(h\\) and \\(e\\) have exact defined values. Quantum Hall devices therefore realize resistance through fixed constants. Actual measurements still have uncertainties arising from contacts, leakage, temperature, excessive current, and the comparison circuitry. Graphene has become important for resistance standards because its electronic structure supports robust quantum Hall behavior under experimentally useful conditions.\n\nThe quantum anomalous Hall effect produces a quantized transverse response without an externally applied magnetic field being required to create Landau levels. Instead, magnetic order and band topology produce a Chern-insulating state. Its first experimental observation was reported in 2013 by a collaboration led by Chang-Zu Chang and colleagues in chromium-doped bismuth–antimony telluride thin films. It is distinct from both an ordinary anomalous Hall signal, which need not be quantized, and the magnetic-field-induced integer quantum Hall effect."
    },
    {
      "heading": "Spin Hall and valley Hall effects",
      "text": "The spin Hall effect is a transverse separation associated with spin angular momentum rather than necessarily with net electric charge. When an electric field drives carriers through a suitable material, spin–orbit coupling can make carriers with different spin orientations acquire opposite transverse responses. Their charge flows may cancel while a transverse spin current remains. A finite sample can then develop opposite spin accumulations at its two edges.\n\nBoth intrinsic and extrinsic mechanisms occur. Intrinsic spin Hall transport depends on the material’s electronic states, whereas extrinsic contributions arise from spin-dependent scattering, including skew scattering and side-jump processes. Unlike the ordinary charge Hall effect, a spin Hall response can exist in a nonmagnetic material without an applied magnetic field. Time-reversal symmetry can permit it because opposite spin components contribute oppositely to transverse charge motion.\n\nThe inverse spin Hall effect converts an injected spin current into a transverse charge signal. Platinum, tantalum, and tungsten are widely studied in this context, although the magnitude and sign of their responses depend on composition, structure, thickness, and interfaces. Direct and inverse conversion connects electrical circuits to magnetic dynamics. A spin Hall material adjoining a ferromagnet can exert a spin–orbit torque on the magnetization, providing a mechanism investigated for magnetic memory and high-frequency devices.\n\nSpin-current measurements require careful interpretation. Spin is not generally conserved in a material with spin–orbit coupling, so defining a bulk spin-current operator is less straightforward than defining conserved charge current. At the device level, measured conversion efficiencies can also include interface transmission, spin relaxation, current shunting, and competing mechanisms. An observed edge polarization or voltage must therefore be connected to a specified transport model.\n\nThe valley Hall effect concerns another electronic label: the valley, meaning a distinct energy extremum in crystal-momentum space. In materials with suitable broken inversion symmetry, different valleys can have opposite Berry curvature. An electric field then drives carriers from opposite valleys in opposite transverse directions. If the valley populations are equal, their charge Hall contributions cancel, but a valley-polarized flow may remain.\n\nGapped graphene-based systems and monolayer transition-metal dichalcogenides provide important examples of valley physics. Optical selection rules can preferentially excite particular valleys, while electrical structures can probe nonlocal responses associated with valley transport. However, a nonlocal voltage alone is not conclusive evidence of a valley Hall mechanism; ordinary current spreading, thermoelectric effects, and other transport processes may contribute. The distinction from the spin Hall effect is the degree of freedom transported: a valley index in one case and spin angular momentum in the other."
    },
    {
      "heading": "Nonlinear, thermal, and other transverse responses",
      "text": "The ordinary Hall effect is usually discussed within linear response, where the transverse current is proportional to the applied electric field. Some materials also exhibit a nonlinear Hall effect, in which a transverse current appears at second order:\n\n\\[j_a^{(2)}=\\chi_{abc}E_bE_c.\\]\n\nThe indices denote spatial directions and repeated indices are summed. A second-order electrical response of this form is forbidden by bulk inversion symmetry, but suitable noncentrosymmetric materials can support it even when time-reversal symmetry is preserved and no external magnetic field is applied.\n\nOne important mechanism is a Berry-curvature dipole: an asymmetric distribution of Berry curvature among occupied momentum states. Time-reversal symmetry can make the ordinary linear charge Hall conductivity vanish while allowing this distribution to generate a second-order transverse response. Inti Sodemann and Liang Fu formulated a widely used theory of this mechanism in 2015. Nonlinear Hall signals have subsequently been investigated in low-symmetry materials, including tungsten ditelluride.\n\nWith sinusoidal excitation, a quadratic response produces both a rectified component and a component at twice the driving frequency. Second-harmonic detection is therefore useful experimentally, but it does not establish the microscopic mechanism by itself. Nonlinear scattering, contact effects, and heating can produce additional signals. Crystal symmetry, angular dependence, frequency dependence, and current scaling help distinguish these possibilities. The nonlinear Hall effect is consequently a probe of electronic geometry only when competing contributions are adequately separated.\n\nThe thermal Hall effect, also called the Righi–Leduc effect, is the appearance of transverse heat transport in response to a longitudinal temperature gradient. Its description uses a thermal-conductivity tensor rather than an electrical-conductivity tensor. Electrons can carry transverse heat in conductors, but a thermal Hall signal can also occur in electrical insulators. There, neutral excitations such as phonons or magnetic excitations may contribute. The absence of electrical conduction therefore does not imply the absence of transverse energy transport.\n\nRelated thermoelectric phenomena mix electrical and thermal responses. In the Nernst effect, a longitudinal temperature gradient in a magnetic field produces a transverse electric field under open-circuit conditions. The reciprocal Ettingshausen effect involves transverse thermal transport driven by electrical current in a magnetic field. These effects are experimentally distinct from an electrically driven Hall voltage, yet can contaminate Hall measurements when current-induced heating creates temperature gradients.\n\nAnother specialized case is the Hall response of a plasma. When electrons and ions respond differently to a magnetic field, an additional term appears in the generalized relation between electric field and current. In a common quasineutral, singly ionized description, this Hall term is proportional to \\(\\mathbf j\\times\\mathbf B/(n_e e)\\). It is important in Hall magnetohydrodynamics, some regimes of magnetic reconnection, and Hall-effect spacecraft thrusters. These systems differ greatly from solid-state Hall plates, but share the underlying importance of transverse motion and the different magnetic responses of charged constituents."
    }
  ],
  "links": [
    "electric-current",
    "magnetic-field",
    "electric-field",
    "condensed-matter-physics",
    "electronic-band-structure",
    "electron",
    "electron-hole",
    "quantum-mechanics",
    "lorentz-force",
    "elementary-charge",
    "drude-model",
    "joule-heating",
    "fermi-surface",
    "semiconductor",
    "temperature",
    "electrical-resistance",
    "measurement-uncertainty",
    "silicon",
    "feedback",
    "direct-current",
    "calibration",
    "magnetization",
    "spin-orbit-coupling",
    "quantum-hall-effect",
    "planck-constant",
    "landau-levels",
    "metrology",
    "international-system-of-units",
    "spin-angular-momentum",
    "phonon",
    "plasma",
    "magnetic-reconnection"
  ],
  "sources": [],
  "license": "https://creativecommons.org/licenses/by/4.0/"
}