{
  "id": "electrical-conductivity",
  "title": "Electrical Conductivity",
  "lang": "en",
  "source_lang": "en",
  "summary": "Electrical conductivity measures how readily a material carries electric current through the motion of electrons, ions, or other charged carriers.",
  "category": "science",
  "subcategory": "physics",
  "type": "concept",
  "aliases": [
    "Electric conductivity",
    "specific conductance"
  ],
  "generated_at": "2026-11-03",
  "model": "pro/gpt-6.1-sol",
  "url": "https://aiwiki.page/en/electrical-conductivity/",
  "translations": {
    "zh-Hans": {
      "url": "https://aiwiki.page/zh/electrical-conductivity/",
      "json": "https://aiwiki.page/zh/electrical-conductivity.json"
    }
  },
  "sections": [
    {
      "heading": "",
      "text": "Electrical conductivity is a material property that describes the response of mobile electric charges to an applied electric field. In a homogeneous, isotropic material under steady conditions, it is the proportionality constant between the electric field and the resulting electric current density. A high conductivity means that a relatively small field produces a substantial current. Metals, salt solutions, semiconductors, and ionized gases conduct by different microscopic processes, while electrical insulators have very low conductivity under their normal operating conditions.\n\nConductivity connects microscopic charge transport with the behavior of wires, electronic devices, batteries, natural waters, and the interior of Earth. Its value depends not only on chemical composition but also on temperature, crystal structure, defects, frequency, and sometimes magnetic field or applied voltage. It is therefore more accurately understood as a response property measured under specified conditions than as an unchanging number assigned to a substance.\n\nThe simplest description uses a single scalar conductivity. More general descriptions require a direction-dependent tensor, a complex frequency-dependent response, or a nonlocal relationship between field and current. These extensions are essential for interpreting anisotropic crystals, alternating-current measurements, nanoscale devices, and quantum transport."
    },
    {
      "heading": "Definition, units, and relation to resistance",
      "text": "The local form of Ohm’s law for an isotropic material is\n\n\\[\\mathbf{J}=\\sigma\\mathbf{E},\\]\n\nwhere \\(\\mathbf{J}\\) is current density in amperes per square metre, \\(\\mathbf{E}\\) is electric field in volts per metre, and \\(\\sigma\\) is electrical conductivity. In the International System of Units, conductivity is measured in siemens per metre, written \\(\\mathrm{S\\,m^{-1}}\\). One siemens is one ampere per volt. In electrochemistry and water analysis, the symbol \\(\\kappa\\) is also commonly used for conductivity.\n\nFor a homogeneous wire of length \\(L\\), uniform cross-sectional area \\(A\\), and negligible contact effects, conductance \\(G\\) and resistance \\(R\\) satisfy\n\n\\[G=\\sigma\\frac{A}{L}, \\qquad R=\\frac{L}{\\sigma A}.\\]\n\nConductance describes an entire specimen or device; conductivity describes its material response after geometry has been accounted for. A short, thick wire has a larger conductance than a long, thin wire made from the same material, even though their conductivities are identical. This distinction becomes especially important when comparing laboratory samples of different sizes.\n\nFor an isotropic conductor, electrical resistivity is the reciprocal quantity,\n\n\\[\\rho=\\frac{1}{\\sigma},\\]\n\nand has units of ohm metres. Neither \\(\\rho\\) nor \\(\\sigma\\) is necessarily independent of field strength. The linear relation applies when the field is sufficiently small that carrier populations and their transport properties remain approximately unchanged. Strong fields can cause substantial heating, change carrier velocities, or produce electrical breakdown. In nonlinear devices, the local slope of a current–voltage curve defines a differential conductance rather than a single field-independent material constant.\n\nConductivity also determines irreversible electrical energy dissipation. The power converted into heat per unit volume is\n\n\\[p=\\mathbf{J}\\cdot\\mathbf{E}=\\sigma E^2\\]\n\nfor an isotropic ohmic material. This is the local expression for Joule heating. At a prescribed current density, the equivalent expression is \\(p=J^2/\\sigma\\), so increasing conductivity reduces dissipation. The distinction between fixed-field and fixed-current conditions explains why statements about conductivity and heating must specify how a circuit is driven.\n\nA reported conductivity consequently requires context: temperature, measurement direction, frequency, composition, and sometimes field strength. For heterogeneous materials, an “effective conductivity” additionally depends on the arrangement and connectivity of their constituent phases, not simply on an average of the conductivities of those phases."
    },
    {
      "heading": "Charge carriers and microscopic transport",
      "text": "Electrical conduction requires mobile carriers of electric charge. In a metal these are principally electrons; in an electrolyte they are positive and negative ions; in a semiconductor they include electrons and holes. A material may contain enormous amounts of electric charge yet conduct poorly because its charges are bound or localized. Conductivity depends on the number of carriers that can move over macroscopic distances and on how effectively they move under an electric field.\n\nFor several independent carrier populations, a useful low-field expression is\n\n\\[\\sigma=\\sum_s n_s|q_s|\\mu_s,\\]\n\nwhere \\(n_s\\) is the number density of carriers of type \\(s\\), \\(q_s\\) their charge, and \\(\\mu_s\\) their positive mobility. Mobility relates the magnitude of the drift velocity to the applied field. Positively and negatively charged carriers drift in opposite directions, but both contribute current in the direction of the applied field. Thermal motion alone does not create a net current in equilibrium because its directional contributions cancel.\n\nThe classical Drude model, introduced by Paul Drude in 1900, treats electrons as mobile particles whose directed motion is interrupted by collisions. For a single population it gives\n\n\\[\\sigma=\\frac{ne^2\\tau}{m^*}, \\qquad \\mu=\\frac{e\\tau}{m^*},\\]\n\nwhere \\(e\\) is the magnitude of the elementary charge, \\(\\tau\\) is a momentum-relaxation time, and \\(m^*\\) is an effective mass. The model captures the competition between acceleration by the field and relaxation of directed momentum. Its assumptions are simplified: different collisions need not relax current equally, and in crystalline solids the effective mass reflects the electronic structure rather than simply the free-electron mass.\n\nA microscopic treatment uses quantum mechanics and the electronic band structure of a solid. Electrons occupy states according to Fermi–Dirac statistics. In an ordinary metal at low temperature, transport is governed predominantly by states near the Fermi energy, because exclusion prevents most deeply occupied states from changing their occupations in response to a weak field. The Pauli exclusion principle is therefore central to metallic transport, even when a classical-looking conductivity formula remains useful.\n\nScattering from lattice vibrations, impurities, boundaries, and other excitations limits drift. The associated mean free path estimates the distance a carrier travels between relevant scattering events. When device dimensions approach this length, boundaries and contacts become integral parts of transport, and a conductivity inferred from macroscopic geometry may no longer represent a size-independent bulk property."
    },
    {
      "heading": "Metals, alloys, and temperature dependence",
      "text": "Ordinary metals have high conductivity because they possess a large density of mobile electronic states. Near \\(20\\,^\\circ\\mathrm{C}\\), representative conductivities are approximately \\(6.3\\times10^7\\ \\mathrm{S\\,m^{-1}}\\) for silver, \\(5.8\\times10^7\\ \\mathrm{S\\,m^{-1}}\\) for copper, and \\(3.5\\times10^7\\ \\mathrm{S\\,m^{-1}}\\) for aluminium. These are approximate values for specified material conditions, not universal constants: purity, mechanical treatment, and temperature can produce measurable differences.\n\nFor many metals near room temperature, resistivity is approximately linear in temperature:\n\n\\[\\rho(T)\\approx\\rho(T_0)\\left[1+\\alpha(T-T_0)\\right].\\]\n\nFor annealed copper near \\(20\\,^\\circ\\mathrm{C}\\), the temperature coefficient \\(\\alpha\\) is about \\(3.9\\times10^{-3}\\ \\mathrm{K^{-1}}\\). Increasing temperature generally increases the population of phonons, the quantized vibrations of the crystal lattice. Electron–phonon scattering then more strongly relaxes electrical current. Conductivity correspondingly decreases, even though the number of conduction electrons changes relatively little.\n\nAt low temperatures, phonon scattering weakens and defects become increasingly important. An approximate description, Matthiessen’s rule, writes the resistivity as a sum of contributions such as\n\n\\[\\rho(T)\\approx\\rho_{\\mathrm{res}}+\\rho_{\\mathrm{ph}}(T).\\]\n\nHere \\(\\rho_{\\mathrm{res}}\\) is residual resistivity associated with impurities and structural defects, while \\(\\rho_{\\mathrm{ph}}\\) is the phonon contribution. The rule is not exact: different scattering mechanisms can interact, and complex band structures can invalidate simple additivity. Nevertheless, the ratio of room-temperature resistivity to low-temperature residual resistivity is widely used to characterize metallic purity and defect content.\n\nAlloying often reduces conductivity because substitutional atoms disturb the periodic potential experienced by electrons. This is why a mechanically strong copper alloy may conduct less well than high-purity copper. Conversely, alloys with deliberately high and relatively temperature-stable resistance are useful for precision resistors and heating elements. Grain boundaries, dislocations, and nanoscale dimensions also alter transport, creating practical trade-offs between conductivity, strength, processability, and reliability.\n\nElectrical transport is closely related to thermal conductivity in metals because electrons carry both charge and energy. The Wiedemann–Franz law states that, under suitable conditions,\n\n\\[\\frac{\\kappa_{\\mathrm e}}{\\sigma T}\\approx \\frac{\\pi^2 k_{\\mathrm B}^2}{3e^2},\\]\n\nwhere \\(\\kappa_{\\mathrm e}\\) is the electronic thermal conductivity and \\(k_{\\mathrm B}\\) is the Boltzmann constant. The relation does not include heat carried by the lattice and can fail when charge and energy currents relax differently."
    },
    {
      "heading": "Semiconductors, insulators, and localized conduction",
      "text": "In a semiconductor, conductivity is highly sensitive to the populations of electrons and holes:\n\n\\[\\sigma=e(n\\mu_n+p\\mu_p),\\]\n\nwhere \\(n\\) and \\(p\\) are their respective concentrations and \\(\\mu_n\\) and \\(\\mu_p\\) their mobilities. Unlike a typical metal, a semiconductor can undergo enormous conductivity changes through controlled impurity addition, illumination, or electrostatic gating. This tunability underlies transistors, photodetectors, and many electronic sensors.\n\nThe band gap separates occupied valence-band states from conduction-band states. In intrinsic material, thermal excitation creates electron–hole pairs. In a simplified nondegenerate description,\n\n\\[n_i\\propto T^{3/2} \\exp\\left(-\\frac{E_g}{2k_{\\mathrm B}T}\\right),\\]\n\nif the temperature dependence of the band gap and effective masses is neglected. For silicon, the band gap is approximately \\(1.12\\) electronvolts near room temperature. The exponential growth of carrier concentration often outweighs the decrease in mobility caused by increasing phonon scattering, so intrinsic semiconductor conductivity generally increases with temperature.\n\nDoping introduces donor or acceptor states. In silicon, phosphorus commonly supplies donor electrons, while boron creates acceptor states associated with hole conduction. At sufficiently low temperature, carriers can remain bound to dopants, producing a freeze-out regime. At intermediate temperatures, ionized dopants often control the carrier concentration; at higher temperatures, intrinsic excitation can dominate. Very heavy doping can produce degenerate behavior closer to that of a metal, showing that “semiconductor” and “conductor” are not separated by a single universal conductivity threshold.\n\nAn electrical insulator generally has too few mobile carriers to support appreciable current under ordinary conditions, but its conductivity is not necessarily exactly zero. Impurities, defects, absorbed water, and interfaces can control its measured leakage. In disordered materials, carriers may occupy localized states and move by thermally assisted hopping rather than by extended band transport. Variable-range hopping permits a compromise between hopping distance and the energy difference between accessible states, leading to temperature dependences distinct from a simple activation law.\n\nStrong fields introduce additional mechanisms, including quantum tunneling, field-assisted release from traps, and impact ionization. These mechanisms can produce nonlinear conduction before irreversible breakdown occurs. In polymers, glasses, ceramics, and thin insulating films, the distinction among bulk conduction, surface leakage, and injection from electrodes is especially important: nominally identical materials can yield very different apparent conductivities when humidity, surface contamination, thickness, or electrode composition changes."
    },
    {
      "heading": "Ionic conduction in liquids, solids, and plasmas",
      "text": "An electrolyte conducts through ion motion rather than through the metallic transport of electrons. Dissolved salts, acids, and bases provide mobile charged species; their contributions depend on concentration, charge, solvation, and mobility. The electric field drives cations and anions in opposite directions. Maintaining a steady current through an external circuit also requires processes at the electrodes, so bulk ionic conductivity must be distinguished from the rates of interfacial electrochemical reactions.\n\nAt sufficiently low concentration, an approximate connection between ionic conductivity and diffusion is provided by the Nernst–Einstein relation:\n\n\\[\\sigma=\\sum_i\\frac{n_iq_i^2D_i}{k_{\\mathrm B}T},\\]\n\nwhere \\(D_i\\) is the diffusion coefficient of species \\(i\\). This expression assumes that relevant ion motions can be treated as independent. In concentrated solutions and many solids, correlations between carriers make that approximation inadequate. Ion association, changes in solvent structure, and increasing viscosity can cause conductivity to increase less rapidly than concentration, or even decrease after reaching a maximum.\n\nThe molar conductivity of an electrolyte is \\(\\Lambda_m=\\sigma/c\\), with \\(c\\) expressed in moles per cubic metre. Its SI unit is \\(\\mathrm{S\\,m^2\\,mol^{-1}}\\). For strong electrolytes at low concentration, interactions between ionic atmospheres reduce molar conductivity as concentration increases. Hydrogen and hydroxide ions have unusually high mobilities in water because proton transfer through the hydrogen-bond network supplements ordinary motion of solvated ions.\n\nAt \\(25\\,^\\circ\\mathrm{C}\\), ideal ultrapure water has a conductivity of approximately \\(0.055\\ \\mathrm{\\mu S\\,cm^{-1}}\\), equivalent to about \\(5.5\\times10^{-6}\\ \\mathrm{S\\,m^{-1}}\\). Its corresponding resistivity is about \\(18.2\\ \\mathrm{M\\Omega\\,cm}\\). Even uncontaminated water conducts weakly because of its self-ionization. Exposure to atmospheric carbon dioxide raises conductivity by introducing additional dissolved ionic species. Typical seawater, by contrast, has conductivity of order \\(4\\)–\\(6\\ \\mathrm{S\\,m^{-1}}\\), depending strongly on temperature and salinity.\n\nIonic conduction also occurs in solids. Vacancies, interstitial sites, and connected migration pathways allow ions to move through certain ceramics, glasses, and polymers. Oxygen-ion conduction in stabilized zirconia and lithium-ion transport in solid electrolytes are technologically important examples. Their conductivity is often thermally activated and strongly influenced by grain boundaries and composition.\n\nIn a plasma, electrons and ions both transport charge. Because electrons are much lighter, they often dominate the electrical response, but collisions, ionization state, and magnetic confinement can strongly modify conductivity. A partially ionized gas and a highly ionized plasma therefore need not obey the same transport scaling."
    },
    {
      "heading": "Directional, magnetic, and frequency-dependent response",
      "text": "A scalar conductivity assumes that current density is parallel to the applied electric field. In an anisotropic material, the more general linear relationship is\n\n\\[J_i=\\sum_j\\sigma_{ij}E_j,\\]\n\nwhere \\(\\sigma_{ij}\\) is the conductivity tensor. A crystal can conduct readily along one axis and poorly along another. Layered graphite, for example, conducts much more effectively within its carbon sheets than perpendicular to them. Texture in polycrystalline materials can preserve some directional dependence even when individual grains have different orientations.\n\nAn applied magnetic field can produce off-diagonal tensor components through the Hall effect. The magnetic part of the Lorentz force deflects moving carriers, causing a transverse electric field to develop when transverse current is blocked. In a simple single-carrier model, the Hall coefficient is \\(R_H=1/(nq)\\), including the sign of the carrier charge. In multiband materials, however, the Hall response depends on carrier populations and mobilities, so it cannot always be interpreted as a direct carrier-count measurement.\n\nConductivity is also frequency dependent. For sinusoidal fields, the current may lag or lead the field, and a complex conductivity represents both dissipative and reactive response. With the time convention \\(e^{-i\\omega t}\\), the Drude model gives\n\n\\[\\sigma(\\omega)=\\frac{\\sigma_0}{1-i\\omega\\tau}.\\]\n\nThe real part describes absorption of electrical energy, while the imaginary part represents a current component in quadrature with the field. At frequencies comparable to or above the scattering rate, carriers cannot establish the same drift response as in a steady field. At still higher frequencies, transitions between electronic bands and other excitations can dominate.\n\nThe distinction between conduction current and polarization current requires a consistent convention. permittivity and conductivity both enter Maxwell’s equations, and some frequency-dependent losses can be represented either as part of a complex permittivity or as an effective conductivity. Reporting the adopted time convention and definitions prevents apparent sign disagreements or double counting.\n\nIn a good conductor, an alternating current and its associated electromagnetic field become concentrated near the surface. This skin effect has an approximate penetration depth\n\n\\[\\delta=\\sqrt{\\frac{2}{\\mu\\sigma\\omega}},\\]\n\nwhen conductivity is predominantly real and displacement current is negligible. Here \\(\\mu\\) is magnetic permeability and \\(\\omega\\) is angular frequency. Skin depth controls high-frequency conductor losses, electromagnetic shielding, and induction heating; it also means that direct-current conductivity alone does not determine a component’s high-frequency resistance."
    },
    {
      "heading": "Measurement methods and metrological limitations",
      "text": "A conductivity measurement generally combines an electrical measurement with a geometrical model. For a uniform bar, resistance yields \\(\\sigma=L/(RA)\\), but uncertainty in dimensions, nonuniform cross sections, and contact resistance can dominate the result. A two-terminal measurement includes both the sample and its electrical connections. This may be acceptable for a highly resistive specimen but can produce substantial error when the sample resistance is small.\n\nThe four-point probe and related four-terminal methods separate current injection from voltage sensing. Two contacts carry current while two others measure the potential difference with negligible current draw. Voltage drops in the current leads and their contacts are thereby largely excluded. The conversion from measured voltage and current to resistivity still requires the correct geometry: probe spacing, specimen thickness, boundaries, and anisotropy all matter.\n\nThin films are often characterized by sheet resistance \\(R_{\\square}\\), reported in ohms per square. For a homogeneous film of thickness \\(t\\),\n\n\\[R_{\\square}=\\frac{\\rho}{t}.\\]\n\nThe phrase “per square” expresses a geometrical property rather than an additional physical dimension. A rectangular film measured along its length has resistance \\(R=R_{\\square}L/W\\), apart from contact and edge effects. The van der Pauw method, developed by Leo van der Pauw in 1958, permits resistivity measurement on many flat, uniformly thick specimens using small peripheral contacts, provided its assumptions about connectivity and material uniformity are satisfied.\n\nFor liquids, a conductivity cell relates measured conductance to conductivity through a cell constant \\(K\\):\n\n\\[\\sigma=KG.\\]\n\nAn ideal parallel-plate geometry gives \\(K=L/A\\), but practical cells are usually calibrated using reference solutions, commonly potassium chloride solutions. calibration is essential because fringe fields, electrode shape, deposits, and ageing affect the effective cell geometry. Alternating excitation reduces some effects of electrode polarization and net electrolysis, although the chosen frequency must also avoid significant capacitive errors.\n\nTemperature control is critical, particularly for electrolytes. A meter may report the measured conductivity at the sample temperature or a compensated value referred to \\(25\\,^\\circ\\mathrm{C}\\). Compensation depends on the sample’s actual temperature response; a coefficient appropriate for one solution is not universally valid. Reliable metrology therefore distinguishes raw measurements, compensation models, and reference conditions.\n\nHigh-resistance measurements require guarding against surface leakage, moisture, and instrument input currents. Very conductive samples require attention to thermal voltages, contact placement, and self-heating. Measurement uncertainty includes these effects as well as calibration uncertainty and dimensional errors."
    },
    {
      "heading": "Engineering, environmental, and geophysical uses",
      "text": "Conductivity is a central parameter in selecting materials for power transmission and electrical interconnections. Copper combines high conductivity with useful mechanical and fabrication properties. Aluminium has lower conductivity per unit cross-sectional area but a much lower mass density, making it attractive for overhead lines. In either case, operating temperature, mechanical loading, corrosion, and connection design influence performance alongside the nominal bulk conductivity.\n\nIn microelectronics, reducing conductor dimensions increases resistance through smaller cross sections and additional scattering at surfaces and grain boundaries. High current densities can also drive atomic redistribution, known as electromigration. Consequently, the most conductive bulk material is not automatically the best interconnect material at every length scale: interface quality, diffusion barriers, manufacturing compatibility, and long-term stability become decisive.\n\nIn electrochemical systems, ionic conductivity affects internal resistance and power loss. A battery electrolyte must carry ions while limiting unwanted electronic conduction that would contribute to self-discharge. Conductivity alone does not determine battery performance; interfacial reaction kinetics, ion selectivity, stability, and mass transport also matter. The same distinction applies to fuel cells, electrolysers, and membrane-based separation systems.\n\nWater conductivity is widely used as a rapid indicator of dissolved ionic content. It can reveal changes in river chemistry, seawater intrusion into an aquifer, or mixing between waters of different origins. However, the relationship between conductivity and total dissolved solids is composition dependent. A solution dominated by sodium chloride and one dominated by calcium bicarbonate can have different conductivities at the same dissolved mass concentration. Conductivity also cannot, by itself, identify a contaminant or establish whether water is safe to drink.\n\nOceanographic instruments measure conductivity together with temperature and pressure to determine salinity under established seawater conventions. Salinity then contributes to estimates of seawater density, which is fundamental to ocean circulation. Because conductivity varies strongly with temperature, simultaneous measurements and suitable equations are necessary; a conductivity reading alone is not a direct salinity measurement.\n\nIn geology, electrical and electromagnetic surveys exploit contrasts among rocks, pore fluids, and mineral deposits. Connected saline pore water can make an otherwise resistive rock relatively conductive, while clay minerals introduce additional surface-conduction mechanisms. Electrical resistivity imaging uses injected current and measured surface potentials, whereas magnetotelluric methods use natural electromagnetic variations to investigate deeper conductivity structures. Their interpretations are not unique: similar effective conductivities can arise from different combinations of porosity, fluid salinity, temperature, partial melt, and conductive minerals."
    },
    {
      "heading": "Historical development and quantum limits",
      "text": "The study of conductivity emerged from efforts to relate current, voltage, material, and geometry quantitatively. Georg Simon Ohm’s 1827 work established the resistance relationships that remain the basis of macroscopic transport measurement. During the nineteenth century, investigations of electrolytes distinguished conduction by dissolved ions from metallic conduction. Michael Faraday connected electrical charge transfer with chemical transformation through his laws of electrolysis, while Friedrich Kohlrausch’s measurements helped establish the independent ionic contributions to limiting molar conductivity.\n\nDrude’s 1900 electron theory provided a mechanical model of metallic conduction, but classical statistical assumptions could not explain all metallic properties. The development of quantum statistics and band theory transformed the subject. Arnold Sommerfeld’s application of Fermi–Dirac statistics to electrons in metals in the late 1920s clarified why only a restricted range of electronic states participates in many responses. Subsequent transport theories incorporated scattering between quantum states and the detailed geometry of energy bands.\n\nIn very small conductors, transport can become ballistic: carriers cross the active region with little internal scattering. The Landauer formula expresses conductance in terms of transmission through quantum channels. For noninteracting, spin-degenerate channels at low temperature,\n\n\\[G=\\frac{2e^2}{h}\\sum_n T_n,\\]\n\nwhere \\(h\\) is the Planck constant and \\(T_n\\) is the transmission probability of channel \\(n\\). A fully transmitting spin-degenerate channel contributes approximately \\(77.5\\ \\mathrm{\\mu S}\\). Here conductance, including the role of contacts and reservoirs, is the natural measurable quantity; assigning a bulk conductivity can obscure the underlying physics.\n\nDisorder provides another limit to classical expectations. Quantum interference can localize electronic states, preventing diffusion even when a simple carrier-count argument would suggest conduction. Interactions between electrons can also generate insulating behavior that cannot be explained solely by an empty conduction band or a large band gap. These phenomena make conductivity an important probe of electronic phases and transitions.\n\nThe quantum Hall effect, discovered in 1980 by Klaus von Klitzing, demonstrates that distinct components of the conductivity tensor can behave very differently. In the integer regime, Hall conductance occurs in plateaus at integer multiples of \\(e^2/h\\), while longitudinal dissipation becomes very small. This quantization supports exceptionally precise resistance standards.\n\nsuperconductivity presents a different departure from ordinary transport. A superconductor supports persistent current and zero measured steady-state resistance below appropriate critical limits. Describing it merely as a material with an extremely large finite conductivity misses its dissipationless response and magnetic properties. Its electrodynamics must distinguish the zero-frequency response, finite-frequency absorption, and the expulsion of magnetic flux rather than treating it as an ordinary metal with a longer scattering time."
    }
  ],
  "links": [
    "electric-field",
    "electric-current",
    "earth",
    "ohms-law",
    "international-system-of-units",
    "electrical-resistance",
    "electrical-resistivity",
    "heat",
    "joule-heating",
    "electric-charge",
    "electron",
    "ion",
    "electron-hole",
    "elementary-charge",
    "momentum",
    "quantum-mechanics",
    "electronic-band-structure",
    "fermi-dirac-statistics",
    "fermi-energy",
    "pauli-exclusion-principle",
    "scattering",
    "temperature",
    "phonon",
    "thermal-conductivity",
    "wiedemann-franz-law",
    "boltzmann-constant",
    "semiconductor",
    "band-gap",
    "silicon",
    "quantum-tunneling",
    "electrolyte",
    "diffusion",
    "viscosity",
    "water",
    "hydrogen-bond",
    "carbon-dioxide",
    "plasma",
    "graphite",
    "magnetic-field",
    "hall-effect",
    "lorentz-force",
    "permittivity",
    "maxwells-equations",
    "alternating-current",
    "skin-effect",
    "four-point-probe",
    "calibration",
    "electrolysis",
    "metrology",
    "measurement-uncertainty",
    "aquifer",
    "density",
    "geology",
    "michael-faraday",
    "planck-constant",
    "quantum-hall-effect",
    "superconductivity"
  ],
  "sources": [],
  "license": "https://creativecommons.org/licenses/by/4.0/"
}