{
  "id": "dew-point",
  "title": "Dew Point",
  "lang": "en",
  "source_lang": "en",
  "summary": "The dew point is the temperature at which a gas becomes saturated with water vapor when cooled at constant pressure and unchanged water content.",
  "category": "science",
  "subcategory": "physics",
  "type": "concept",
  "aliases": [
    "Dew-point temperature",
    "water dew point"
  ],
  "generated_at": "2026-11-03",
  "model": "pro/gpt-6.1-sol",
  "url": "https://aiwiki.page/en/dew-point/",
  "translations": {
    "zh-Hans": {
      "url": "https://aiwiki.page/zh/dew-point/",
      "json": "https://aiwiki.page/zh/dew-point.json"
    }
  },
  "sections": [
    {
      "heading": "",
      "text": "The dew point is the temperature to which air or another gas must be cooled, at constant pressure and unchanged water-vapor content, to reach saturation with respect to liquid water. At this temperature, water vapor can coexist in equilibrium with liquid water; further cooling generally causes condensation. Although commonly associated with droplets on grass or windows, the dew point describes the moisture state of the gas, not the temperature of an object or the amount of dew that will form.\n\nDew point is widely used in weather observation, atmospheric research, building engineering, and industrial gas processing. Unlike relative humidity, it does not change simply because air is warmed at approximately constant pressure without gaining or losing moisture. It therefore provides a useful measure of atmospheric moisture, while also identifying when cold surfaces, cooling equipment, or gas pipelines may begin to collect liquid water. Its interpretation depends on pressure, the distinction between liquid water and ice, and whether the gas is close enough to equilibrium for saturation calculations to apply."
    },
    {
      "heading": "Thermodynamic definition and physical basis",
      "text": "Air contains water vapor mixed with nitrogen, oxygen, and other gases. In the approximately ideal-gas conditions of the lower atmosphere, water vapor contributes a partial pressure, conventionally written \\(e\\). The equilibrium vapor pressure above a flat surface of pure liquid water is the saturation vapor pressure, \\(e_s(T)\\). It rises strongly with temperature. The dew-point temperature \\(T_d\\) is defined, to this approximation, by\n\n\\[e=e_s(T_d).\\]\n\nCooling a gas mixture at constant total pressure and fixed composition leaves the water-vapor mole fraction, and hence its partial pressure, essentially unchanged until condensation begins. Saturation occurs because the equilibrium vapor pressure falls as temperature decreases—not because cold air possesses a literal storage capacity that has become full. The familiar statement that warm air “holds more water” is shorthand for a temperature-dependent equilibrium condition.\n\nAt a molecular level, water molecules continually enter and leave a liquid surface. At saturation, the opposing transfers balance. In thermodynamic terms, the chemical potentials of water in the vapor and liquid phases are equal. Cooling changes the relative stability of these phases, eventually favoring the liquid. Condensation releases latent heat, so the actual cooling of saturated air differs from that of unsaturated air.\n\nThe temperature dependence of saturation vapor pressure is described by the Clausius–Clapeyron equation. Neglecting liquid volume relative to vapor volume and treating the vapor as ideal gives\n\n\\[\\frac{d\\ln e_s}{dT}=\\frac{L_v}{R_vT^2},\\]\n\nwhere \\(L_v\\) is the latent heat of vaporization per unit mass, \\(R_v\\) is the specific gas constant of water vapor, and \\(T\\) is absolute temperature in kelvins. Near ordinary surface temperatures, saturation vapor pressure increases by roughly 6–7% per kelvin, although the rate varies with temperature.\n\nThese definitions refer to equilibrium over a flat surface of pure water. Dissolved substances reduce water’s activity, while strongly curved droplets have a different equilibrium vapor pressure because of surface tension. Consequently, a tiny atmospheric droplet or a saline surface need not behave exactly like the reference liquid used to define dew point. High-accuracy gas measurements also account for nonideal interactions through an enhancement factor that relates saturation in a gas mixture to the vapor pressure of pure water."
    },
    {
      "heading": "Relationships to humidity measures and calculation",
      "text": "Relative humidity expresses how close the water-vapor pressure is to saturation at the current air temperature. When both quantities are referenced to liquid water,\n\n\\[\\mathrm{RH}=100\\frac{e}{e_s(T)} =100\\frac{e_s(T_d)}{e_s(T)}.\\]\n\nThis explains why relative humidity can fall sharply during daytime warming even when dew point changes little. Air at \\(20^\\circ\\mathrm{C}\\) with a dew point near \\(9.3^\\circ\\mathrm{C}\\) has approximately 50% relative humidity. If heated to \\(30^\\circ\\mathrm{C}\\) without moisture exchange and at unchanged pressure, its dew point remains near \\(9.3^\\circ\\mathrm{C}\\), but relative humidity falls to about 28%.\n\nDew point is closely related to water-vapor mixing ratio, the mass of vapor per mass of dry air. For an ideal mixture,\n\n\\[r=\\epsilon\\frac{e}{p-e},\\]\n\nwhere \\(p\\) is total pressure and \\(\\epsilon\\approx0.622\\) is the ratio of the molecular masses of water and dry air. At \\(p=1000\\) hPa, a dew point of \\(20^\\circ\\mathrm{C}\\) corresponds to a vapor pressure of approximately 23.4 hPa and a mixing ratio of about 14.9 grams per kilogram of dry air. At the same dew point but lower pressure, the mixing ratio is larger.\n\nDew point is therefore not interchangeable with every other moisture measure. Absolute humidity is water-vapor mass per volume, which also depends on gas temperature. Specific humidity is vapor mass divided by the total mass of moist air. Dew point determines vapor pressure, but total pressure is additionally needed to obtain mixing ratio or specific humidity. This distinction matters when comparing surface observations with measurements at altitude or in pressurized equipment.\n\nA common approximation for computing dew point is the Magnus-type expression\n\n\\[\\gamma=\\ln\\left(\\frac{\\mathrm{RH}}{100}\\right)+\\frac{aT}{b+T}, \\qquad T_d=\\frac{b\\gamma}{a-\\gamma}.\\]\n\nHere \\(T\\) and \\(T_d\\) are numerical temperatures in degrees Celsius. One widely used coefficient pair for liquid water is \\(a=17.625\\) and \\(b=243.04^\\circ\\mathrm{C}\\). Different coefficient sets cover different temperature ranges and reference phases; they are not universally interchangeable, especially at very low temperatures.\n\nThe difference \\(T-T_d\\) is called the dew-point depression. A small depression indicates near-saturation, whereas a large depression indicates relatively dry air. Dew-point errors calculated from relative humidity become particularly sensitive to humidity errors in dry conditions because the conversion contains a logarithm. Accurate calculations consequently require a suitable saturation-vapor-pressure formulation, a clearly identified water-or-ice reference, and realistic treatment of measurement uncertainty."
    },
    {
      "heading": "Dew point, frost point, and supersaturation",
      "text": "Below \\(0^\\circ\\mathrm{C}\\), saturation requires an explicit distinction between liquid water and ice. Liquid droplets can remain unfrozen below their normal freezing temperature; this is supercooling. Dew point may therefore be defined relative to supercooled liquid water even when its numerical value is negative. The corresponding temperature for equilibrium with ice is the frost point.\n\nThe equilibrium vapor pressure over ice is lower than that over supercooled liquid water at the same subzero temperature. For a given low vapor pressure, the frost-point temperature is consequently higher than the water-referenced dew point. For example, vapor in equilibrium with liquid water at approximately \\(-10^\\circ\\mathrm{C}\\) has a frost point near \\(-8.9^\\circ\\mathrm{C}\\). The precise conversion depends on the vapor-pressure equations used.\n\nThis distinction has direct observational consequences. Air can be unsaturated relative to liquid water while supersaturated relative to ice. An ice crystal may then grow while a nearby supercooled droplet evaporates. That vapor-pressure difference is central to the Wegener–Bergeron–Findeisen process, through which ice particles grow in mixed-phase clouds. A reported relative humidity of 100% is therefore incomplete unless its reference phase is known, especially in cold-cloud research.\n\nDew and frost also describe different surface processes. Dew forms when water vapor condenses as liquid droplets. Hoarfrost forms by direct deposition of vapor onto ice. Frozen dew forms when droplets first condense and subsequently freeze. A white surface coating can additionally be rime, produced when supercooled fog droplets strike an object and freeze. These deposits cannot be distinguished solely from the air’s reported dew point; surface temperature, liquid droplets, and the history of freezing also matter.\n\nSaturation does not always produce immediate bulk condensation. Formation of a new droplet requires a sufficiently favorable nucleus or enough supersaturation to overcome the energetic cost of creating a curved liquid surface. Atmospheric particles commonly provide cloud condensation nuclei, and existing wet surfaces offer ready sites for condensation. In very clean gases, measurable supersaturation can persist. Conversely, hygroscopic particles may take up water below 100% relative humidity because dissolved material lowers the equilibrium vapor pressure.\n\nThe same phase ambiguity affects instruments. A cooled mirror below freezing may carry liquid, ice, or a mixture. If the instrument measures mirror temperature without identifying the condensate, its reading can be misinterpreted as either dew point or frost point. Reliable low-temperature measurement therefore requires control or identification of the condensed phase, not merely a precise thermometer."
    },
    {
      "heading": "Measurement methods and their development",
      "text": "Early quantitative humidity measurement combined temperature observation with the appearance of condensation. John Frederic Daniell introduced a condensation hygrometer in 1820, using evaporative cooling to lower the temperature of a glass vessel until dew appeared. Such instruments established a direct operational approach: cool a surface, identify the onset or disappearance of condensate, and measure the surface temperature. Modern instruments automate that principle and improve control of surface condition and thermal gradients.\n\nA chilled-mirror hygrometer cools a reflective surface, commonly with a thermoelectric device. An optical system detects a change in reflected or scattered light as condensate forms. Feedback adjusts cooling to maintain a small, stable deposit, and a thermometer measures the mirror temperature. Once the condensate is in equilibrium with the sample gas, the mirror temperature represents the dew point or frost point at the instrument’s operating pressure.\n\nChilled-mirror instruments are valuable as reference devices because their measurement is closely connected to the physical definition. Nevertheless, contamination can change a surface’s water activity, interfere with optical detection, or alter nucleation behavior. Temperature differences between the sensing element and the actual surface also introduce errors. At very low moisture levels, equilibration can be slow because only tiny quantities of water reach the mirror.\n\nMany routine weather stations do not measure dew point directly. They measure air temperature and relative humidity with electronic sensors and calculate dew point. Capacitive humidity sensors use a moisture-sensitive dielectric whose electrical properties change as it absorbs water. Resistive sensors measure changes in electrical resistance. A psychrometer instead compares dry-bulb and wetted-bulb temperatures; evaporation cools the wetted sensor, and humidity is inferred using pressure-dependent heat-and-mass-transfer relationships.\n\nIndustrial trace-moisture instruments may use metal-oxide sensors, electrolytic methods, or spectroscopic absorption by water vapor. These generally measure a moisture-dependent signal or water-vapor concentration and convert it to dew point using pressure and a saturation relation. Their useful ranges, response times, susceptibility to contamination, and calibration requirements differ substantially.\n\nSample handling is often as important as the detector. Water can be adsorbed by tubing, seals, and instrument walls and later released, producing delayed or biased readings. Leaks can admit humid ambient air into a dry sample, while a cold section of tubing can remove water before it reaches the sensor. Calibration therefore considers the complete measurement arrangement, including gas pressure, flow, temperature, and equilibration. Metrological traceability links reported values to recognized standards through documented calibrations and uncertainties; it does not eliminate errors caused by an unrepresentative sample."
    },
    {
      "heading": "Weather systems, fog, and cloud formation",
      "text": "Meteorologists use dew point to distinguish changes in moisture from changes caused mainly by heating and cooling. A warm afternoon may have much lower relative humidity than the preceding morning even though its dew point is similar. A substantial dew-point increase, by contrast, usually indicates moisture addition or transport, although changing pressure, vertical mixing, and local surface exchanges can also affect the observation. Maps of surface dew point help identify maritime air, continental air, moisture boundaries, and the inflow feeding storms.\n\nFog forms when suspended droplets reduce visibility near the ground, conventionally below 1 kilometre in meteorological reporting. Cooling air toward its dew point is one route to fog, but not the only one. Radiation fog develops when the ground loses energy overnight and cools adjacent moist air. Advection fog can form when moist air moves across a colder surface. Mixing and evaporation can also produce saturation, as when cold air passes over relatively warm water and receives additional vapor.\n\nDew-point depression helps estimate the height at which a rising air parcel first becomes saturated. Before condensation, an unsaturated parcel cools through adiabatic expansion at approximately \\(9.8^\\circ\\mathrm{C}\\) per kilometre, while its dew point commonly decreases by about \\(2^\\circ\\mathrm{C}\\) per kilometre. A useful near-surface approximation for the lifting condensation level is\n\n\\[z_{\\mathrm{LCL}}\\approx125(T-T_d),\\]\n\nwhere \\(z_{\\mathrm{LCL}}\\) is in metres and the temperature difference is in degrees Celsius or kelvins. A depression of \\(8^\\circ\\mathrm{C}\\) thus suggests a condensation level around 1 kilometre above the parcel’s starting height.\n\nThis is a parcel estimate rather than a universal cloud-base formula. Entrainment, atmospheric layering, precipitation, and variations in moisture with height can produce different cloud bases. Weather balloons measure vertical profiles of temperature and humidity, allowing forecasters to assess elevated moist layers and dry layers that a surface dew point cannot reveal.\n\nHigh low-level dew points can contribute to substantial energy release when air rises and water vapor condenses, but moisture alone does not determine thunderstorm occurrence or severity. Atmospheric instability, lifting mechanisms, wind profiles, and inhibiting layers are also important. Sharp moisture boundaries, such as the dryline of the central United States, can organize convergence and help initiate storms when other conditions permit.\n\nDew-point observations also support aviation weather reporting and visibility assessment. A narrowing temperature–dew-point spread may accompany increasing fog risk, but it is not a deterministic forecast. Wind, cloud cover, ground conditions, and the persistence of cooling determine whether saturation actually develops."
    },
    {
      "heading": "Surface dew, ecosystems, and climate interpretation",
      "text": "An exposed surface can become colder than the surrounding air by emitting thermal radiation toward a clear sky. Grass blades, leaves, roofs, and vehicle bodies may therefore fall below the local dew point even while the measured air temperature remains above it. This explains why dew can form without a weather station reporting 100% relative humidity. The relevant comparison is between the surface temperature and the dew point of the air immediately next to that surface.\n\nClear skies favor strong nighttime radiative cooling, while clouds return more longwave radiation toward the ground and often limit it. Wind has competing effects: air movement supplies vapor to a condensing surface but can also transfer sensible heat from warmer air and prevent sufficient cooling. The resulting dew amount depends on surface temperature, aerodynamic exchange, available moisture, radiation, and the latent heat released during condensation. Dew point alone cannot predict the accumulated water.\n\nDew participates in the water cycle on scales that differ from rainfall. It may wet leaf surfaces, soil particles, rocks, and biological soil crusts without producing a measurable rain event. In some dry environments, this intermittent surface moisture influences the activity of lichens and other organisms. Certain plants can absorb water through leaves, but the importance of foliar uptake varies with species, leaf properties, and environmental conditions. Dew deposited on vegetation is not automatically equivalent to water entering roots or replenishing groundwater.\n\nLeaf wetness also has agricultural significance. Many plant pathogens depend on a combination of temperature and the duration of surface moisture. Dew-point measurements help estimate when wetting may occur, but canopy conditions can differ markedly from standard meteorological observations. Leaves at different heights exchange radiation differently and encounter different ventilation. Measurements taken above a crop may consequently miss saturation within a sheltered canopy.\n\nAt larger scales, dew point helps characterize atmospheric moisture and changes in the land–atmosphere water exchange. Evapotranspiration, moisture transport, soil drying, and vegetation all influence near-surface vapor pressure. Irrigated land may supply additional water vapor, while drought can suppress evaporation and alter humidity patterns. Coastal locations are strongly affected by nearby sea-surface conditions and air movement between land and sea.\n\nIn climate-change analysis, rising temperature does not require dew point to increase at the same rate everywhere. Saturation vapor pressure rises with warming, but actual atmospheric moisture depends on water availability and circulation. Relative humidity, dew point, and specific humidity therefore describe related but distinct aspects of climate. Long-term dew-point records require attention to sensor changes, station moves, observation times, and reporting practices before trends are attributed to physical causes."
    },
    {
      "heading": "Buildings, cooling systems, and moisture control",
      "text": "In buildings, condensation occurs when a surface falls below the dew point of the air in contact with it. A room at \\(22^\\circ\\mathrm{C}\\) and 50% relative humidity has a dew point near \\(11^\\circ\\mathrm{C}\\). A window edge, metal pipe, or structural connection colder than that can collect water even though the room’s average relative humidity is moderate. A thermal bridge creates a local pathway for heat flow and can produce precisely such a cold spot.\n\nThe location of condensation depends on the full temperature and moisture distribution. Water vapor can enter assemblies through diffusion, but moving air can also carry substantial moisture through gaps. In cold weather, indoor air leaking outward may cool enough to condense within an envelope. In hot, humid weather, outdoor air leaking inward may encounter air-conditioned surfaces below its dew point. These mechanisms cannot be evaluated from indoor relative humidity alone.\n\nWater can also accumulate in porous materials without visible droplets. Adsorption and capillary effects allow materials to retain moisture under conditions below saturation relative to a flat water surface. Surface temperature, moisture storage, rain exposure, and drying paths all affect performance. Persistent dampness can support material deterioration and microbial growth, but a single dew-point calculation does not establish the duration or extent of wetting.\n\nIn heating, ventilation, and air-conditioning systems, a cooling coil removes moisture when part of its surface is colder than the entering air’s dew point. Vapor condenses on the coil, releasing latent heat that the refrigeration system must remove in addition to the sensible heat associated with lowering air temperature. Condensate is collected and drained. The leaving air’s state depends on coil temperature, airflow, heat-transfer effectiveness, and the fraction of air that does not closely approach the cold surface.\n\nDehumidification and cooling are therefore related but distinct processes. Air may be cooled and dried at a coil, then reheated to provide a desired supply temperature without restoring the removed moisture. Conversely, heating moist air lowers its relative humidity but does not itself lower its dew point. Ventilation can either add or remove indoor moisture depending on the moisture content of the incoming air, rather than simply whether outdoor air feels cooler.\n\nEngineers represent these processes on a psychrometric chart, which relates dry-bulb temperature, moisture content, enthalpy, relative humidity, and other properties at a specified pressure. Dew point is found by following a constant moisture-content line toward saturation. Pressure must be specified because the relationship between vapor pressure and water mass per unit mass of dry air changes with elevation."
    },
    {
      "heading": "Pressurized gases, process control, and specialized dew points",
      "text": "In industrial systems, a dew-point value is meaningful only when its measurement pressure is known. For a gas with fixed water-vapor mole fraction \\(x_v\\), the ideal-mixture relation is\n\n\\[e=x_vp.\\]\n\nIncreasing total pressure therefore raises the water-vapor partial pressure and raises the dew point, even though the proportion of water molecules has not changed. A pressure dew point is measured or specified at the operating pressure; an atmospheric dew point refers to approximately atmospheric pressure.\n\nThe difference can be large. Air containing about 100 parts per million water vapor by volume has a vapor pressure near 10 Pa at 1 bar absolute, but near 80 Pa at 8 bar absolute. These correspond approximately to frost points of \\(-42^\\circ\\mathrm{C}\\) and \\(-23^\\circ\\mathrm{C}\\), respectively. The example also illustrates why low-temperature specifications should identify whether values refer to liquid water or ice. Absolute pressure, rather than gauge pressure, is required in the calculation.\n\nCompressed-air systems exploit these relationships. Compression followed by cooling can cause liquid water to separate because the vapor partial pressure has increased. Refrigerated dryers cool the gas and remove condensate, while desiccant dryers remove water by adsorption and can attain substantially lower pressure dew points. A dew-point specification describes the moisture state of the delivered gas, but does not by itself establish the absence of oil, particles, or other contaminants.\n\nWater-dew-point control is also important in natural-gas processing, high-purity gas distribution, and manufacturing. Condensed water can contribute to corrosion, interfere with instruments, or promote blockages under suitable conditions. In natural gas, water can additionally participate in gas-hydrate formation, which depends on pressure, temperature, and gas composition. At elevated pressures, nonideal mixture behavior requires more detailed thermodynamic calculations than the simple partial-pressure approximation.\n\nThe expression “dew point” is also applied to substances other than water. A hydrocarbon dew point is the temperature at which a hydrocarbon liquid phase first appears from a gas mixture at specified pressure. Unlike water dew point in a dilute gas, it depends strongly on the distribution of multiple condensable components and may display complex phase behavior. An acid dew point in combustion exhaust refers to the onset of condensation involving acidic species, notably sulfuric acid under relevant flue-gas conditions.\n\nThese specialized dew points must not be substituted for one another. A gas can meet a water-dew-point requirement yet condense hydrocarbons, and an exhaust stream can develop acid condensate at a temperature far above its water dew point. Process specifications accordingly identify the condensable substance, reference pressure, equilibrium model, and measurement method."
    }
  ],
  "links": [
    "temperature",
    "pressure",
    "water",
    "condensation",
    "ideal-gas",
    "atmosphere-of-earth",
    "vapor-pressure",
    "thermodynamics",
    "chemical-potential",
    "latent-heat",
    "kelvin",
    "thermodynamic-activity",
    "surface-tension",
    "relative-humidity",
    "measurement-uncertainty",
    "frost-point",
    "cloud-condensation-nuclei",
    "spectroscopy",
    "calibration",
    "metrological-traceability",
    "adiabatic-process",
    "electromagnetic-radiation",
    "heat",
    "water-cycle",
    "groundwater",
    "evapotranspiration",
    "climate-change",
    "diffusion",
    "adsorption"
  ],
  "sources": [],
  "license": "https://creativecommons.org/licenses/by/4.0/"
}