{
  "id": "desorption",
  "title": "Desorption",
  "lang": "en",
  "source_lang": "en",
  "summary": "Desorption is the release of a substance from a surface into a surrounding gas or liquid, governed by molecular interactions, equilibrium, kinetics, and transport.",
  "category": "science",
  "subcategory": "chemistry",
  "type": "concept",
  "aliases": [],
  "generated_at": "2026-11-05",
  "model": "pro/gpt-6.1-sol",
  "url": "https://aiwiki.page/en/desorption/",
  "translations": {
    "zh-Hans": {
      "url": "https://aiwiki.page/zh/desorption/",
      "json": "https://aiwiki.page/zh/desorption.json"
    }
  },
  "sections": [
    {
      "heading": "",
      "text": "Desorption is the process by which a substance attached to a surface leaves that surface and enters a surrounding gas or liquid. It is the reverse of adsorption and occurs at interfaces such as those between a solid and a gas or between a solid and a liquid. Desorption governs the release of gases from porous materials, the removal of contaminants from soils, the regeneration of industrial adsorbents, and the departure of reaction products from catalysts."
    },
    {
      "heading": "Physical basis",
      "text": "An adsorbed substance, or adsorbate, is held at a surface by interactions that may range from relatively weak intermolecular attraction to strong chemical bonding. The material providing the surface is the adsorbent. Although adsorption is a surface process, the relevant surface can include the extensive internal walls of pores rather than only the outside of a particle.\n\nIn physical adsorption, binding arises mainly from van der Waals forces and other noncovalent interactions. In chemical adsorption, attachment involves the formation of chemical bonds with surface sites. Physically adsorbed species can often be released under milder conditions than chemisorbed species, but the required conditions depend on the particular surface, adsorbate, and surrounding medium.\n\nDesorption requires an adsorbed species to leave its bound state. This commonly involves crossing an energy barrier. In thermal desorption, fluctuations associated with temperature supply the energy needed for escape. Desorption can also be stimulated by light, electron bombardment, changes in electrical potential, or displacement by another adsorbing substance.\n\nA departing species need not have the same molecular form as the species bound to the surface. For example, two adsorbed hydrogen atoms can combine and leave as a hydrogen molecule, a process called recombinative desorption.\n\nDistinction from related processes\n\nDesorption is not identical to every process that releases material:\n\n- Absorption involves entry into the bulk of a material, rather than accumulation at an interface. Material stored within a bulk phase may first have to migrate to a surface before it can desorb.\n- Evaporation is the transfer of a substance from a liquid to a gas. Release of adsorbed water from a solid is desorption, although it can occur alongside evaporation of liquid water within pores.\n- Dissolution transfers material from a solid or other phase into a solution. The disappearance of part of a solid into solution is not, by itself, desorption.\n- Outgassing describes gas release from a material and can include desorption, diffusion from the interior, evaporation, and decomposition."
    },
    {
      "heading": "Equilibrium and driving forces",
      "text": "Adsorption and desorption usually occur simultaneously. At chemical equilibrium, their rates are equal, so the average amount adsorbed remains constant even though individual molecules continue to arrive and leave.\n\nThe thermodynamic direction of transfer depends on chemical potential. Reducing the concentration or partial pressure of an adsorbate in the surrounding fluid generally favors its net release. This principle underlies desorption by evacuation, flushing with a clean gas, or washing with a solution containing little of the adsorbed substance.\n\nFor a simple gas–surface system described by the Langmuir model, the equilibrium fractional coverage is\n\n\\[\\theta=\\frac{KP}{1+KP},\\]\n\nwhere \\(\\theta\\) is the fraction of occupied adsorption sites, \\(P\\) is the adsorbate's partial pressure, and \\(K\\) is an equilibrium coefficient. The model assumes equivalent sites, single-layer occupancy, and no interactions between adsorbed particles. At fixed temperature, lowering \\(P\\) lowers the equilibrium coverage and therefore promotes net desorption.\n\nHeating also commonly promotes release because adsorption is often exothermic. Its effects are both thermodynamic, shifting the equilibrium distribution, and kinetic, accelerating escape from bound states. This behavior is not universal across all chemically complex surfaces.\n\nAt solid–liquid interfaces, desorption can also be influenced by pH, dissolved salts, competing solutes, and the identity of the solvent. Such changes may alter surface charge, adsorbate speciation, or the relative stability of the adsorbed and dissolved states."
    },
    {
      "heading": "Kinetics",
      "text": "A common description of thermally activated desorption is the Polanyi–Wigner equation:\n\n\\[r_{\\mathrm{des}} =-\\frac{d\\theta}{dt} =\\nu\\theta^n \\exp\\left(-\\frac{E_{\\mathrm{des}}}{RT}\\right),\\]\n\nwhere:\n\n- \\(r_{\\mathrm{des}}\\) is the rate of decrease in surface coverage;\n- \\(\\nu\\) is a kinetic prefactor;\n- \\(n\\) is the desorption order;\n- \\(E_{\\mathrm{des}}\\) is the molar activation energy for desorption;\n- \\(R\\) is the gas constant;\n- \\(T\\) is absolute temperature.\n\nThis expression connects desorption to chemical kinetics. Its simplest form treats the activation energy and prefactor as constants, although both may vary with coverage or surface structure.\n\nFirst-order behavior often describes independent molecules leaving equivalent sites. Second-order behavior can arise when two adsorbed species must combine before departure. Zeroth-order behavior can occur during desorption from multilayer films while enough condensed adsorbate remains to maintain an approximately constant exposed area.\n\nSurface release versus transport\n\nThe measured rate of release need not equal the elementary rate of escape from surface sites. In porous particles, molecules may have to move through narrow pores, repeatedly adsorb and desorb, and cross a fluid boundary layer before reaching the bulk fluid. Consequently, diffusion or other mass-transfer processes may control the observed response.\n\nThis distinction matters when interpreting experiments. Slow release may reflect strong binding, slow transport, heterogeneous adsorption sites, or a combination of these effects. A single fitted rate constant does not necessarily identify the molecular mechanism."
    },
    {
      "heading": "Methods of inducing and measuring desorption",
      "text": "Thermal desorption\n\nThermal desorption uses heating to release adsorbed substances. In temperature-programmed desorption, a sample is heated according to a controlled schedule while the evolved material is measured, often by mass spectrometry.\n\nThe resulting peaks provide information about binding states, reaction pathways, and desorption kinetics. Peak temperature alone is not a direct measurement of binding energy: it also depends on heating rate, kinetic order, coverage, and possible readsorption. Overlapping peaks can make interpretation ambiguous.\n\nPressure reduction and purging\n\nEvacuation or a clean carrier-gas stream reduces the adsorbate's partial pressure around the surface. This suppresses readsorption and favors net release.\n\nIndustrial adsorption systems exploit this principle in pressure-swing adsorption, where an adsorbent is loaded at higher pressure and regenerated at lower pressure. Vacuum-assisted variants use subatmospheric pressure during regeneration.\n\nLiquid-phase elution\n\nAt solid–liquid interfaces, desorption can be induced by changing solvent composition, pH, salt concentration, or the concentration of competing substances. Chromatography uses differences in affinity for stationary and mobile phases to separate substances; changing the mobile phase can release retained components.\n\nStimulated desorption\n\nPhotons, electrons, and ions can induce desorption through electronic excitation, bond breaking, or energy transfer. Electrochemical desorption can occur when an applied potential changes surface bonding or charge. These methods are useful in surface analysis and processing, although irradiation or applied potentials may also change the surface or the released species."
    },
    {
      "heading": "Applications",
      "text": "Adsorbent regeneration. Activated carbon, zeolites, and other porous materials can be reused after retained substances are removed. Regeneration conditions must balance recovery against energy demand, incomplete release, and possible damage to the adsorbent.\n\nHeterogeneous catalysis. In catalysis at solid surfaces, products must leave active sites so further reactions can occur. Excessively strong product binding can hinder turnover. The effective catalyst must support both the necessary surface reactions and subsequent product release.\n\nEnvironmental transport. Desorption affects the mobility of nutrients, metals, and organic contaminants in soils, sediments, and groundwater. A substance initially retained by solids may later re-enter pore water as environmental conditions change.\n\nAnalytical chemistry. Desorption transfers collected substances into instruments for identification and quantification. Thermal desorption is widely used to introduce compounds trapped on sampling materials, while laser desorption methods can release analytes for mass spectrometric analysis.\n\nVacuum technology. Desorption from chamber walls contributes to the gas load in vacuum systems. Controlled heating, often called bakeout, accelerates removal of adsorbed gases, especially water, so that lower pressures can subsequently be maintained."
    },
    {
      "heading": "Hysteresis and practical limitations",
      "text": "Adsorption and desorption do not always follow the same path. At a given pressure or dissolved concentration, the retained amount can depend on whether the material was previously being loaded or emptied. This behavior is called adsorption–desorption hysteresis.\n\nIn porous materials, hysteresis can arise from capillary condensation, pore blocking, network effects, and metastable fluid configurations. In soils and other heterogeneous solids, apparent hysteresis can also reflect slow diffusion, strong binding sites, or structural changes. A difference between measured adsorption and desorption curves does not by itself establish irreversible chemical attachment.\n\nComplete regeneration may be difficult because some species remain trapped, bind strongly, or react with the surface. Conversely, aggressive heating or chemical treatment may decompose the adsorbate or damage the adsorbent. Desorption therefore denotes a specific transfer process, not a guarantee that the original substance can be recovered unchanged or that the surface can be restored completely."
    }
  ],
  "links": [
    "adsorption",
    "physisorption",
    "van-der-waals-forces",
    "chemisorption",
    "temperature",
    "evaporation",
    "chemical-equilibrium",
    "chemical-potential",
    "pressure",
    "ph",
    "solvent",
    "activation-energy",
    "gas-constant",
    "chemical-kinetics",
    "diffusion",
    "mass-spectrometry",
    "chromatography",
    "catalysis",
    "groundwater"
  ],
  "sources": [],
  "license": "https://creativecommons.org/licenses/by/4.0/"
}