{
  "id": "characteristic-impedance",
  "title": "Characteristic Impedance",
  "lang": "en",
  "source_lang": "en",
  "summary": "Characteristic impedance is the voltage-to-current ratio of a single traveling wave on a transmission line, determining its reflection and matching behavior.",
  "category": "science",
  "subcategory": "physics",
  "type": "concept",
  "aliases": [
    "Surge impedance",
    "Natural impedance of a transmission line"
  ],
  "generated_at": "2026-11-05",
  "model": "pro/gpt-6.1-sol",
  "url": "https://aiwiki.page/en/characteristic-impedance/",
  "translations": {
    "zh-Hans": {
      "url": "https://aiwiki.page/zh/characteristic-impedance/",
      "json": "https://aiwiki.page/zh/characteristic-impedance.json"
    }
  },
  "sections": [
    {
      "heading": "",
      "text": "Characteristic impedance, usually denoted \\(Z_0\\), is the ratio of voltage to current for a single traveling wave on a uniform transmission line. It is determined by the line’s geometry, materials, and frequency, rather than by its length or terminating load. Measured in ohms, it is an electrical impedance, but it is not generally the same as the line’s electrical resistance or the impedance measured at the input of a finite cable. Characteristic impedance governs how signals propagate, how much of a wave is reflected at a discontinuity, and how transmission lines are matched to sources and loads."
    },
    {
      "heading": "Physical meaning",
      "text": "A transmission line stores electric and magnetic energy continuously along its length. Examples include coaxial cables, paired wires, and conducting traces above a reference plane on a circuit board. Their behavior is described using distributed capacitance and inductance, together with conductor and dielectric losses.\n\nFor a wave traveling in one direction, the voltage and current are not independent: their ratio is fixed by the properties of the line. This ratio is the characteristic impedance.\n\nWith current defined as positive in the direction of increasing coordinate \\(z\\), sinusoidal voltage and current can be written as\n\n\\[V(z)=V^+e^{-\\gamma z}+V^-e^{\\gamma z},\\]\n\n\\[I(z)=\\frac{V^+}{Z_0}e^{-\\gamma z} -\\frac{V^-}{Z_0}e^{\\gamma z},\\]\n\nwhere \\(V^+\\) and \\(V^-\\) are forward- and backward-traveling voltage amplitudes, and \\(\\gamma\\) is the propagation constant. Thus,\n\n\\[\\frac{V_{\\text{forward}}}{I_{\\text{forward}}}=Z_0, \\qquad \\frac{V_{\\text{backward}}}{I_{\\text{backward}}}=-Z_0.\\]\n\nThe minus sign follows from the chosen current reference direction. If both waves are present, the ratio of total voltage to total current generally varies with position and is not equal to \\(Z_0\\).\n\nAn ideal, uniform, semi-infinite line has input impedance \\(Z_0\\): an outgoing wave never encounters an end from which a reflection can return. A finite line terminated in \\(Z_0\\) has the same input impedance because its load produces no reflected wave."
    },
    {
      "heading": "Distributed-circuit formulation",
      "text": "A uniform line can be represented by four parameters per unit length:\n\nParameter | Meaning | Unit\n\\(R\\) | Series resistance of the conductors | \\(\\Omega/\\mathrm{m}\\)\n\\(L\\) | Series inductance | \\(\\mathrm{H}/\\mathrm{m}\\)\n\\(G\\) | Shunt conductance, representing dielectric leakage and loss | \\(\\mathrm{S}/\\mathrm{m}\\)\n\\(C\\) | Shunt capacitance | \\(\\mathrm{F}/\\mathrm{m}\\)\n\nFor sinusoidal steady state with time dependence \\(e^{j\\omega t}\\), the telegrapher’s equations are\n\n\\[\\frac{dV}{dz}=-(R+j\\omega L)I, \\qquad \\frac{dI}{dz}=-(G+j\\omega C)V,\\]\n\nwhere \\(j^2=-1\\) and \\(\\omega\\) is angular frequency. They give\n\n\\[Z_0=\\sqrt{\\frac{R+j\\omega L}{G+j\\omega C}},\\]\n\nand\n\n\\[\\gamma=\\alpha+j\\beta =\\sqrt{(R+j\\omega L)(G+j\\omega C)}.\\]\n\nHere \\(\\alpha\\) is the attenuation constant and \\(\\beta\\) is the phase constant. The square-root branches are chosen consistently with the physical propagation direction and passive behavior.\n\nIn general, \\(Z_0\\) is a complex number and varies with frequency. The distributed parameters themselves may also depend on frequency, particularly because of conductor skin effect and the frequency-dependent properties of the dielectric.\n\nLossless and low-loss lines\n\nFor an ideal lossless line, \\(R=G=0\\), so\n\n\\[Z_0=\\sqrt{\\frac{L}{C}}, \\qquad v_{\\mathrm p}=\\frac{1}{\\sqrt{LC}},\\]\n\nwhere \\(v_{\\mathrm p}\\) is the phase velocity.\n\nThe characteristic impedance is then real even though the line dissipates no energy. This distinguishes it from electrical resistance: a real voltage-to-current ratio can describe power carried away by a traveling wave, not only power converted into heat.\n\nFor a low-loss line satisfying \\(R\\ll\\omega L\\) and \\(G\\ll\\omega C\\),\n\n\\[Z_0\\approx\\sqrt{\\frac{L}{C}}.\\]\n\nThis approximation explains why many cables are specified by a nearly constant nominal impedance over a useful frequency range."
    },
    {
      "heading": "Reflections and impedance matching",
      "text": "When a wave reaches a load of impedance \\(Z_L\\), the voltage reflection coefficient at the load is\n\n\\[\\Gamma_L=\\frac{Z_L-Z_0}{Z_L+Z_0}.\\]\n\nThis is the ratio of reflected to incident voltage amplitude. For an ideal line with real \\(Z_0\\):\n\n- Matched load: \\(Z_L=Z_0\\), giving \\(\\Gamma_L=0\\).\n- Open circuit: \\(Z_L\\rightarrow\\infty\\), giving \\(\\Gamma_L=+1\\).\n- Short circuit: \\(Z_L=0\\), giving \\(\\Gamma_L=-1\\).\n\nReflected and incident waves combine through superposition, producing position-dependent voltage and current. For a lossless line, their pattern is commonly characterized by the voltage standing-wave ratio:\n\n\\[\\mathrm{VSWR}=\\frac{1+|\\Gamma_L|}{1-|\\Gamma_L|},\\]\n\nfor \\(|\\Gamma_L|<1\\).\n\nFor a real, positive \\(Z_0\\), the fraction of incident power reflected at a load is \\(|\\Gamma_L|^2\\). This simple power interpretation requires care for lossy lines with complex characteristic impedance.\n\nImpedance matching can suppress reflections, but reflection-free termination and maximum power transfer are not identical requirements in every circuit. Zero reflection requires \\(Z_L=Z_0\\). Maximum power transfer from a source with complex source impedance instead requires a conjugate match to that source impedance."
    },
    {
      "heading": "Characteristic impedance versus input impedance",
      "text": "The input impedance of a finite uniform line of length \\(\\ell\\) is\n\n\\[Z_{\\mathrm{in}} = Z_0 \\frac{Z_L+Z_0\\tanh(\\gamma\\ell)} {Z_0+Z_L\\tanh(\\gamma\\ell)}.\\]\n\nFor a lossless line, \\(\\gamma=j\\beta\\), giving\n\n\\[Z_{\\mathrm{in}} = Z_0 \\frac{Z_L+jZ_0\\tan(\\beta\\ell)} {Z_0+jZ_L\\tan(\\beta\\ell)}.\\]\n\nConsequently, the impedance seen by a source depends on the load, line length, and frequency, even when the characteristic impedance remains essentially constant.\n\nA lossless quarter-wavelength line, for example, transforms a finite nonzero load according to\n\n\\[Z_{\\mathrm{in}}=\\frac{Z_0^2}{Z_L}.\\]\n\nThis is the basis of a quarter-wave impedance transformer.\n\nA cable labeled “50 ohms” therefore does not normally measure 50 ohms between its conductors with a direct-current resistance meter. That label describes its traveling-wave behavior. A resistance meter instead measures conductor resistance, insulation leakage, or the attached termination, depending on its connections."
    },
    {
      "heading": "Geometry and materials",
      "text": "Characteristic impedance is controlled by how a structure stores electric and magnetic energy. Greater capacitance relative to inductance lowers \\(Z_0\\); greater inductance relative to capacitance raises it.\n\nFor an ideal coaxial line with inner-conductor radius \\(a\\), outer-conductor inner radius \\(b\\), and a homogeneous filling material,\n\n\\[Z_0=\\frac{1}{2\\pi}\\sqrt{\\frac{\\mu}{\\varepsilon}} \\ln\\!\\left(\\frac{b}{a}\\right),\\]\n\nwhere \\(\\mu\\) is magnetic permeability and \\(\\varepsilon\\) is electric permittivity. For a nonmagnetic material with relative permittivity \\(\\varepsilon_r\\),\n\n\\[Z_0\\approx \\frac{60}{\\sqrt{\\varepsilon_r}} \\ln\\!\\left(\\frac{b}{a}\\right)\\ \\Omega.\\]\n\nFor circuit-board transmission lines, conductor width and thickness, distance from the reference plane, and dielectric properties all affect impedance. Microstrip structures have fields distributed partly through the substrate and partly through the surrounding medium, so their behavior is usually calculated with effective material parameters or electromagnetic field solvers.\n\nCommon nominal values include 50 ohms for many radio-frequency instruments and interconnections, 75 ohms for many video and cable-distribution systems, and 100 ohms differential impedance for many balanced data links. These are design conventions, not fundamental constants."
    },
    {
      "heading": "Relation to electromagnetic wave impedance",
      "text": "Characteristic impedance is closely related to, but distinct from, electromagnetic wave impedance. For a plane wave in a homogeneous, lossless, isotropic medium, the electric- to magnetic-field ratio is\n\n\\[\\eta=\\frac{E}{H}=\\sqrt{\\frac{\\mu}{\\varepsilon}}.\\]\n\nIn vacuum this is approximately \\(377\\ \\Omega\\). This ratio involves the electric field and magnetic field, rather than conductor voltage and current.\n\nFor a transverse electromagnetic transmission-line mode, the two impedances are connected through conductor geometry. The coaxial-line formula, for example, is the medium’s wave impedance multiplied by the dimensionless factor \\(\\ln(b/a)/(2\\pi)\\). A 50-ohm air-filled coaxial line therefore does not imply that the wave impedance of air is 50 ohms.\n\nIn hollow waveguides, mode impedances depend on frequency and cutoff. Moreover, definitions based on equivalent voltage and current may depend on normalization conventions. A single scalar transmission-line impedance is therefore not sufficient for every guided electromagnetic structure."
    },
    {
      "heading": "Applications and measurement",
      "text": "Characteristic impedance is central to radio-frequency engineering, high-speed digital electronics, antenna feeding, and power-system transient analysis. The term surge impedance is particularly common in studies of traveling voltage and current surges on power lines.\n\nIn digital circuits, transmission-line effects become important when propagation delay is appreciable compared with signal rise or fall time. Clock frequency alone is not a sufficient criterion: a relatively slow sequence of sharp-edged pulses can still generate significant reflections.\n\nPractical characterization commonly uses:\n\n- Time-domain reflectometry: a fast transition is launched into a line, and returning reflections reveal impedance changes and their locations.\n- Vector network analysis: frequency-dependent reflection and transmission measurements are used to characterize a line or extract its parameters with an appropriate model.\n\nMeasured results depend on connector transitions, calibration reference planes, fixtures, and the assumed line model. A nominal impedance specifies a design target, not perfect uniformity at every point."
    },
    {
      "heading": "Scope and limitations",
      "text": "A single characteristic impedance describes a uniform line operating in a specified mode. Coupled conductors can support multiple modes, such as differential and common modes, with different impedances and velocities. Their general treatment may require impedance and admittance matrices.\n\nAbrupt bends, connectors, vias, branches, and changes in dielectric geometry create discontinuities that cannot always be represented by a simple change between two uniform-line impedances. At sufficiently high frequencies, radiation, higher-order modes, and frequency-dependent losses may require a full electromagnetic treatment based on Maxwell’s equations."
    }
  ],
  "links": [
    "transmission-line",
    "electrical-impedance",
    "capacitance",
    "inductance",
    "electric-current",
    "complex-number",
    "skin-effect",
    "dielectric",
    "electrical-resistance",
    "superposition-principle",
    "impedance-matching",
    "permittivity",
    "electric-field",
    "magnetic-field",
    "maxwells-equations"
  ],
  "sources": [],
  "license": "https://creativecommons.org/licenses/by/4.0/"
}