{
  "id": "brayton-cycle",
  "title": "Brayton Cycle",
  "lang": "en",
  "source_lang": "en",
  "summary": "The Brayton cycle is a thermodynamic cycle that models gas-turbine engines and other systems using compression, constant-pressure heating, expansion, and constant-pressure cooling.",
  "category": "science",
  "subcategory": "physics",
  "type": "concept",
  "aliases": [
    "Joule cycle",
    "Joule–Brayton cycle",
    "Constant-pressure cycle"
  ],
  "generated_at": "2026-11-04",
  "model": "pro/gpt-6.1-sol",
  "url": "https://aiwiki.page/en/brayton-cycle/",
  "translations": {
    "zh-Hans": {
      "url": "https://aiwiki.page/zh/brayton-cycle/",
      "json": "https://aiwiki.page/zh/brayton-cycle.json"
    }
  },
  "sections": [
    {
      "heading": "",
      "text": "The Brayton cycle is a thermodynamic cycle in which a gaseous working fluid is compressed, heated at approximately constant pressure, expanded to produce work, and cooled at approximately constant pressure. It is the principal idealized model for gas-turbine power plants and aircraft gas-turbine engines. In its simplest ideal form, compression and expansion are reversible adiabatic processes, while heat addition and heat rejection occur at two different constant pressures. Practical engines depart from this model because of component inefficiencies, pressure losses, changing fluid properties, and combustion."
    },
    {
      "heading": "Historical development",
      "text": "The cycle takes its name from the American engineer George Brayton, who developed a constant-pressure internal-combustion engine in the nineteenth century. His 1872 engine used reciprocating machinery rather than the continuously rotating compressor and turbine associated with modern gas turbines. Air was compressed separately before fuel burned during admission to a power cylinder.\n\nThe name Joule cycle reflects earlier analysis associated with James Prescott Joule. Terminology varies between engineering traditions, but Brayton cycle and Joule cycle commonly designate the same idealized sequence of processes.\n\nThe cycle became especially important with the development of practical gas turbines. Their performance depended on advances in compressor aerodynamics, high-temperature materials, turbine cooling, and manufacturing, rather than on the thermodynamic cycle alone."
    },
    {
      "heading": "Ideal cycle and its four processes",
      "text": "The standard air-standard model treats the working fluid as an ideal gas of unchanged composition circulating through a closed sequence of states. Combustion is replaced by external heat addition, and exhaust and fresh-air intake are replaced by heat rejection. The further assumption of constant specific heat capacities is often called the cold-air-standard approximation.\n\nNumbering the states in the direction of operation gives four processes:\n\nProcess | Ideal description | Physical role\n\\(1\\rightarrow2\\) | Isentropic compression | A compressor raises fluid pressure and temperature, consuming work.\n\\(2\\rightarrow3\\) | Constant-pressure heat addition | A heater or idealized combustor raises fluid temperature.\n\\(3\\rightarrow4\\) | Isentropic expansion | A turbine produces work as fluid pressure and temperature fall.\n\\(4\\rightarrow1\\) | Constant-pressure heat rejection | A cooler, or the environment in an open-cycle interpretation, returns the fluid to its initial state.\n\nAn isentropic process maintains constant entropy. In this model it is both adiabatic and internally reversible; a real adiabatic compressor or turbine generally generates entropy and is therefore not isentropic.\n\nOn a pressure–volume diagram, the two constant-pressure processes are joined by compression and expansion curves. On a temperature–entropy diagram, ideal compression and expansion appear as vertical lines. For the internally reversible cycle, the enclosed area on the latter diagram represents net heat input, equal to net work output per cycle.\n\nOpen and closed implementations\n\nIn an open-cycle gas turbine, atmospheric air enters a compressor, fuel is added and burned, and the combustion products expand through a turbine before being discharged. The working fluid does not physically return to the compressor. The cycle is closed conceptually by treating the surroundings as the source of fresh air and the recipient of exhaust heat.\n\nIn a closed-cycle system, the same working fluid circulates through a compressor, heater, turbine, and cooler. Heating may come from an external combustion system, a nuclear reactor, or concentrated solar energy. Closed systems permit working fluids other than air, including helium and carbon dioxide.\n\nThese arrangements must be distinguished from the ideal cycle: either an open or a closed installation can be analyzed using a Brayton-type model, but neither automatically satisfies its ideal assumptions."
    },
    {
      "heading": "Work, heat, and thermal efficiency",
      "text": "For steady-flow components, neglecting changes in kinetic energy and potential energy, the first law of thermodynamics relates heat and shaft work to changes in specific enthalpy. Taking compressor work input and turbine work output as positive magnitudes,\n\n\\[w_c=h_2-h_1, \\qquad w_t=h_3-h_4.\\]\n\nThe heat transfers per unit mass are\n\n\\[q_{\\mathrm{in}}=h_3-h_2, \\qquad q_{\\mathrm{out}}=h_4-h_1,\\]\n\nwhere \\(q_{\\mathrm{out}}\\) is the positive magnitude of rejected heat. Consequently,\n\n\\[w_{\\mathrm{net}}=w_t-w_c=q_{\\mathrm{in}}-q_{\\mathrm{out}},\\]\n\nand thermal efficiency is\n\n\\[\\eta_{\\mathrm{th}} =\\frac{w_{\\mathrm{net}}}{q_{\\mathrm{in}}} =1-\\frac{h_4-h_1}{h_3-h_2}.\\]\n\nWith constant specific heat capacity \\(c_p\\), enthalpy differences become \\(c_p\\Delta T\\), giving\n\n\\[\\eta_{\\mathrm{th}} =1-\\frac{T_4-T_1}{T_3-T_2}.\\]\n\nAll temperatures used in temperature ratios must be absolute temperatures, normally expressed in kelvins.\n\nDependence on pressure ratio\n\nDefine the compressor pressure ratio as\n\n\\[r_p=\\frac{p_2}{p_1}=\\frac{p_3}{p_4},\\]\n\nwhere the second equality assumes no pressure loss during heating or cooling. For isentropic ideal-gas processes with constant\n\n\\[\\gamma=\\frac{c_p}{c_v},\\]\n\nthe temperature ratios satisfy\n\n\\[\\frac{T_2}{T_1} =\\frac{T_3}{T_4} =r_p^{(\\gamma-1)/\\gamma}.\\]\n\nSubstitution yields the familiar ideal Brayton-cycle efficiency:\n\n\\[\\boxed{ \\eta_{\\mathrm{th}} =1-\\frac{1}{r_p^{(\\gamma-1)/\\gamma}} }.\\]\n\nWithin these assumptions, efficiency increases with pressure ratio. This does not imply that arbitrarily high pressure ratios are useful or feasible. At fixed compressor-inlet and turbine-inlet temperatures, increasing pressure ratio eventually eliminates the available temperature rise for heat addition and reduces net work toward zero.\n\nThe cycle also remains subject to the second law of thermodynamics. Its efficiency is below that of a Carnot cycle operating between the same minimum and maximum temperatures, because Brayton-cycle heat addition and rejection occur over temperature ranges rather than entirely at the extreme temperatures."
    },
    {
      "heading": "Specific work and the optimum pressure ratio",
      "text": "Thermal efficiency and net work per unit mass are different performance measures. Under constant-property ideal assumptions, let\n\n\\[a=r_p^{(\\gamma-1)/\\gamma}.\\]\n\nFor fixed \\(T_1\\) and \\(T_3\\),\n\n\\[w_{\\mathrm{net}} =c_p\\left[ T_3\\left(1-\\frac{1}{a}\\right) -T_1(a-1) \\right].\\]\n\nMaximizing this expression gives\n\n\\[a_{\\mathrm{opt}}=\\sqrt{\\frac{T_3}{T_1}},\\]\n\nor\n\n\\[r_{p,\\mathrm{opt}} =\\left(\\frac{T_3}{T_1}\\right)^{ \\gamma/[2(\\gamma-1)] }.\\]\n\nAt this maximum-specific-work condition,\n\n\\[T_2=T_4=\\sqrt{T_1T_3}.\\]\n\nThis pressure ratio maximizes ideal specific work, not thermal efficiency, plant profitability, or aircraft propulsive efficiency. Actual design optima depend on component efficiencies, cooling requirements, operating conditions, and system configuration.\n\nCompressor work and back-work ratio\n\nA substantial fraction of turbine output is required to drive the compressor. The back-work ratio is\n\n\\[\\mathrm{BWR}=\\frac{w_c}{w_t}.\\]\n\nBecause the useful output is the difference between two relatively large quantities, modest changes in compressor or turbine performance can produce significant changes in net output. This sensitivity is particularly important during starting, at part load, and at high ambient temperature."
    },
    {
      "heading": "Real-cycle departures",
      "text": "Component irreversibility\n\nActual compression requires more work than isentropic compression to the same outlet pressure. Actual expansion produces less work than isentropic expansion from the same inlet state to the same outlet pressure. Common isentropic-efficiency definitions are\n\n\\[\\eta_c =\\frac{h_{2s}-h_1}{h_2-h_1}, \\qquad \\eta_t =\\frac{h_3-h_4}{h_3-h_{4s}},\\]\n\nwhere the subscript \\(s\\) denotes an isentropic reference state at the specified outlet pressure.\n\nFriction, turbulent mixing, leakage, and other irreversible processes generate entropy and reduce useful output. Pressure losses in intake systems, combustors, ducts, exhaust systems, and heat exchangers further reduce performance.\n\nFluid properties and combustion\n\nSpecific heat capacities vary with temperature, particularly over the large temperature range of a gas turbine. In an open engine, combustion also changes fluid composition and adds fuel mass. Accurate analysis therefore uses temperature- and composition-dependent properties rather than a single constant value of \\(\\gamma\\).\n\nThe heat supplied to the ideal working fluid is not identical to fuel chemical-energy input. Plant efficiency may also include combustion losses, mechanical losses, generator losses, and auxiliary power consumption. Reported fuel-based efficiencies depend on whether fuel energy is expressed using its higher or lower heating value.\n\nTemperature limits and operating conditions\n\nHigher turbine-inlet temperature generally increases specific work and can improve practical efficiency, but material temperatures, creep, oxidation, and cooling requirements impose constraints. Cooling air extracted from the compressor protects components while altering the cycle’s mass and energy balances.\n\nHotter compressor-inlet air increases compression work. In open gas turbines it also lowers inlet-air density, often reducing the mass flow and power output of a given machine. Part-load performance depends on control strategy and component operating characteristics; the simple ideal pressure-ratio formula does not capture these effects."
    },
    {
      "heading": "Modified Brayton cycles",
      "text": "Recuperation or regeneration\n\nA recuperator transfers energy from turbine exhaust to compressed fluid before external heating. This reduces the required heat input without changing ideal compressor or turbine work, provided pressure losses are neglected.\n\nFor the simple constant-property cycle, recuperation is useful only when turbine exhaust is hotter than compressor discharge:\n\n\\[T_4>T_2.\\]\n\nIts benefit therefore tends to be greater at lower pressure ratios. At sufficiently high pressure ratio, the exhaust is too cool relative to the compressor discharge to provide useful preheating. Real gains depend on exchanger effectiveness, pressure loss, cost, and size.\n\nIntercooling\n\nDividing compression into stages and cooling the fluid between stages reduces compressor work. For ideal stages with equal efficiency and perfect intercooling to a common inlet temperature, equal stage pressure ratios minimize total compression work.\n\nIntercooling alone does not necessarily increase thermal efficiency: the cooler compressor discharge can require more subsequent heat addition. It is often paired with recuperation.\n\nReheat\n\nDividing expansion into stages and adding heat between them increases turbine work. It also increases heat input and commonly raises exhaust temperature. Reheat can improve specific output without necessarily improving simple-cycle efficiency; recuperation may recover part of the hotter exhaust’s energy.\n\nCombined-cycle and cogeneration systems\n\nIn a combined-cycle power plant, gas-turbine exhaust supplies heat to a second power cycle, commonly a Rankine steam cycle. This extracts additional work from energy that a simple-cycle plant would discharge to the surroundings.\n\nIn cogeneration, exhaust heat instead, or additionally, supplies useful process or building heat. Overall fuel utilization can be high, but an efficiency that counts useful heat and electricity is not directly comparable with electrical efficiency alone.\n\nSupercritical carbon dioxide systems\n\nBrayton-type cycles using carbon dioxide near and above its critical point are studied and developed for several heat sources. Compression near the critical region can require relatively little work because of the fluid’s high density and strongly varying properties.\n\nMany configurations use extensive recuperation and split-flow or recompression arrangements. Their behavior cannot be represented accurately by the constant-\\(\\gamma\\) ideal-gas efficiency formula; a real-fluid equation of state and detailed heat-exchanger analysis are required."
    },
    {
      "heading": "Applications and reversed operation",
      "text": "Brayton-cycle analysis supports the design of stationary gas turbines, aircraft engines, marine propulsion machinery, and closed-cycle power converters.\n\nIn aircraft engines, the distribution of useful output differs by engine type. A turbojet directs much of the available energy into exhaust acceleration; a turbofan uses turbine work to drive a fan; turboprop and turboshaft engines deliver substantial shaft power. Their full performance analysis must include inlet, nozzle, and propulsive effects beyond the simple shaft-power cycle.\n\nOperated in reverse, the reversed Brayton cycle, also called the Bell–Coleman cycle or gas refrigeration cycle, consumes net work to transfer heat from a lower-temperature region to a higher-temperature region. It uses compression, high-pressure cooling, expansion, and low-pressure heat absorption. Applications include aircraft air-cycle cooling and some cryogenic systems. Unlike vapor-compression refrigeration, the basic gas-cycle model does not rely on a phase transition of the working fluid."
    }
  ],
  "links": [
    "thermodynamics",
    "adiabatic-process",
    "james-prescott-joule",
    "ideal-gas",
    "heat-capacity",
    "entropy",
    "kinetic-energy",
    "potential-energy",
    "first-law-of-thermodynamics",
    "enthalpy",
    "kelvin",
    "second-law-of-thermodynamics",
    "carnot-cycle",
    "friction",
    "temperature",
    "combustion",
    "density",
    "combined-cycle-power-plant",
    "combined-heat-and-power",
    "carbon-dioxide",
    "critical-point",
    "equation-of-state",
    "phase-transition"
  ],
  "sources": [],
  "license": "https://creativecommons.org/licenses/by/4.0/"
}