{
  "id": "bandwidth",
  "title": "Bandwidth",
  "lang": "en",
  "source_lang": "en",
  "summary": "Bandwidth describes a frequency range or a system’s data-transfer capacity, with distinct definitions in communications, electronics, networking, and computing.",
  "category": "science",
  "subcategory": "physics",
  "type": "concept",
  "aliases": [],
  "generated_at": "2026-11-02",
  "model": "pro/gpt-6.1-sol",
  "url": "https://aiwiki.page/en/bandwidth/",
  "translations": {
    "zh-Hans": {
      "url": "https://aiwiki.page/zh/bandwidth/",
      "json": "https://aiwiki.page/zh/bandwidth.json"
    }
  },
  "sections": [
    {
      "heading": "",
      "text": "Bandwidth is the width of a frequency interval or, in a different but closely related usage, the rate at which a communication or computing system can transfer data. In electronics and communications, it usually describes the range of frequencies occupied by a signal or passed by a device, measured in hertz. In computer networks and computer architecture, it commonly denotes a transfer capacity measured in bits or bytes per second. These meanings are connected by communication theory, but they are not interchangeable: a channel occupying a particular frequency band does not have a uniquely determined data rate.\n\nBandwidth is central to the design of radio systems, optical links, electronic instruments, Internet connections, and memory systems. It affects how rapidly signals can change, how finely events can be resolved, how much information can be transmitted, and how competing users share resources. Its precise interpretation depends on what is being measured, where the measurement is made, and the convention used to define a frequency boundary or a transfer rate."
    },
    {
      "heading": "Frequency bandwidth and data-transfer bandwidth",
      "text": "In its frequency-domain meaning, bandwidth is the difference between an upper and a lower frequency boundary:\n\n\\[B=f_{\\mathrm H}-f_{\\mathrm L}.\\]\n\nA device that passes frequencies from 100 MHz to 110 MHz therefore has a bandwidth of 10 MHz, even though it operates near 105 MHz. Its operating frequency and its bandwidth describe different properties. A low-pass system is often assigned a bandwidth equal to its upper cutoff frequency because its useful response extends downward to zero frequency. A bandpass system instead has both lower and upper cutoffs.\n\nFrequency is measured in hertz, equivalent to cycles per second, within the International System of Units. Bandwidth can also be expressed using angular frequency, conventionally in radians per second. Because angular frequency satisfies \\(\\omega=2\\pi f\\), an angular-frequency bandwidth is \\(2\\pi\\) times the corresponding bandwidth in hertz. Equations involving bandwidth must therefore be interpreted with their frequency convention intact.\n\nIn networking, bandwidth usually means a nominal or available data-transfer rate. A 1 Gbit/s link can nominally transfer one billion bits per second at the layer to which that rating applies. This says nothing directly about whether the physical signal occupies 100 MHz, 500 MHz, or some other frequency interval. The relationship depends on modulation, coding, parallel channels, noise, and the physical medium.\n\nUnits also require care. A byte ordinarily contains eight bits, so 1 GB/s corresponds to 8 Gbit/s before any distinction between payload and overhead. Decimal prefixes are customary in communication rates: 1 Mbit/s means \\(10^6\\) bit/s. Binary prefixes such as mebi and gibi mean powers of two and are written Mi and Gi. Confusing MB/s with Mbit/s introduces a factor of eight; confusing decimal and binary prefixes introduces a separate discrepancy.\n\nThe terms wideband, broadband, and narrowband are relative rather than universal frequency categories. A channel can be narrow compared with its carrier frequency yet wide compared with the frequency range over which its propagation characteristics change. Fractional bandwidth provides one useful comparison:\n\n\\[B_{\\mathrm{frac}}=\\frac{f_{\\mathrm H}-f_{\\mathrm L}}{f_{\\mathrm c}},\\]\n\nwhere \\(f_{\\mathrm c}\\) is a specified center frequency. Some applications use the arithmetic mean of the edges; others use a geometric center or a nominal carrier. Consequently, a fractional-bandwidth value is fully meaningful only when its center-frequency convention is known."
    },
    {
      "heading": "Spectral definitions and bandwidth conventions",
      "text": "A signal’s frequency content is described mathematically by a Fourier transform or a related spectral representation. An ideal band-limited signal has no spectral content outside a specified interval. Most real signals are not strictly band-limited: switching transitions, finite-duration pulses, and practical modulation schemes produce spectral components that extend beyond their main frequency region. Engineering bandwidth definitions therefore usually describe a useful or dominant part of a spectrum rather than an exact boundary between presence and absence.\n\nFor a filter, amplifier, or other linear system, bandwidth is often defined using its frequency response \\(H(f)\\). The common half-power convention places a boundary where transmitted power has fallen to half its reference value. With consistent impedance conditions, this corresponds to an amplitude ratio of \\(1/\\sqrt{2}\\), approximately 0.707. Expressed in decibels, the level is approximately \\(-3.0103\\) dB. A “3 dB bandwidth” is thus tied to a specified reference level, usually the low-frequency gain or the peak passband response.\n\nOther definitions serve different purposes. Null-to-null bandwidth is the separation between specified spectral zeros, often the first zeros on either side of a principal lobe. Occupied bandwidth encloses a stated fraction of total signal power. In a commonly used 99% convention, the lower and upper boundaries leave 0.5% of the mean power below and above the interval, respectively. Emission measurements may instead specify bandwidth at a particular number of decibels below a reference level. These definitions can give substantially different numerical answers for the same signal.\n\nNoise calculations often use equivalent noise bandwidth. For a low-pass filter with one-sided integration, it can be defined as\n\n\\[B_{\\mathrm n} = \\frac{\\displaystyle\\int_0^\\infty |H(f)|^2\\,df} {|H(0)|^2}.\\]\n\nThis is the width of an ideal rectangular filter that would pass the same white-noise power while having the same reference gain. A first-order low-pass filter with 3 dB cutoff \\(f_{\\mathrm c}\\) has \\(B_{\\mathrm n}=\\pi f_{\\mathrm c}/2\\), not \\(f_{\\mathrm c}\\). Confusing these bandwidths causes systematic errors in noise estimates.\n\nFor a signal with power spectral density \\(S(f)\\), power in a specified frequency interval is obtained by integrating \\(S(f)\\) across that interval. A density expressed in watts per hertz becomes a power only after integration. One-sided and two-sided spectral conventions allocate power differently between positive and negative frequencies, so their factors of two must be handled consistently.\n\nNo bandwidth specification is therefore complete without its criterion. A filter’s 3 dB bandwidth, a transmitter’s occupied bandwidth, and a receiver’s equivalent noise bandwidth answer different questions even when all three are expressed in hertz."
    },
    {
      "heading": "Time resolution, pulses, and sampling",
      "text": "Bandwidth constrains how rapidly a system can respond to changes. A slow system suppresses high-frequency components, rounding a sharp transition and spreading a short pulse over time. This connection underlies much of signal processing: compactness in time generally requires a broad frequency distribution, while a narrowly concentrated spectrum generally implies an extended waveform.\n\nFor a first-order low-pass system, the relationship between its 10–90% rise time \\(t_{\\mathrm r}\\) and its 3 dB bandwidth is\n\n\\[t_{\\mathrm r}B \\approx 0.35.\\]\n\nThus a 100 MHz first-order response has a rise time of approximately 3.5 ns. The numerical factor is not universal. It changes with filter order, response shape, and the definition of rise time. Systems with resonant peaking can show fast transitions accompanied by overshoot and ringing, so bandwidth alone does not specify waveform fidelity.\n\nPulse duration and spectral width are similarly related. For an ideal transform-limited Gaussian optical pulse, the full-width-at-half-maximum intensity duration and intensity frequency width satisfy approximately\n\n\\[\\Delta t\\,\\Delta \\nu=0.441.\\]\n\nA pulse with frequency-dependent phase, such as a chirped pulse, can have a larger time–bandwidth product. The Fourier relationship is mathematically related to the uncertainty principle, but ordinary engineering pulse broadening does not require a quantum-mechanical explanation.\n\nThe sampling theorem gives another fundamental bandwidth connection. An ideal baseband signal containing no frequencies at or above \\(B\\) can be reconstructed from uniformly spaced samples when the sampling rate exceeds \\(2B\\), under the theorem’s assumptions. Spectral overlap caused by insufficient sampling produces aliasing: different continuous-time frequencies become indistinguishable in the sampled data. An analog antialiasing filter is therefore placed before an analog-to-digital converter to suppress components that would fold into the desired band.\n\nThe theoretical limiting rate is not usually a practical design target. Real antialiasing filters need a transition band, converters have finite precision and timing errors, and reconstruction filters are not ideal. Oversampling provides room for these nonidealities. Bandpass sampling can sometimes digitize a high-frequency band at a rate much lower than twice its highest frequency, but only with carefully chosen sampling rates and sufficiently isolated spectral bands.\n\nSampling rate and bandwidth are consequently distinct specifications. An instrument sampling at 1 gigasample per second does not automatically have a usable analog bandwidth of 500 MHz. Its input amplifier, converter response, aperture behavior, and antialiasing arrangements may impose a substantially lower limit. Conversely, equivalent-time sampling instruments can characterize repetitive waveforms whose bandwidth exceeds what their real-time sampling rate alone would suggest."
    },
    {
      "heading": "Electronic circuits and measurement instruments",
      "text": "In electronic circuits, bandwidth emerges from energy storage, dissipation, propagation delay, and active-device dynamics. Capacitance and inductance store electrical and magnetic energy, while resistance dissipates it. Their interaction creates characteristic time constants and resonances. Even a circuit designed as a simple amplifier contains parasitic capacitances and inductances that eventually limit its high-frequency response.\n\nA resistor–capacitor low-pass circuit illustrates the basic mechanism. For a series resistance \\(R\\) driving a capacitance \\(C\\), with output measured across the capacitor,\n\n\\[H(f)=\\frac{1}{1+j2\\pi fRC}, \\qquad f_{\\mathrm c}=\\frac{1}{2\\pi RC}.\\]\n\nIncreasing either \\(R\\) or \\(C\\) reduces bandwidth because the capacitor charges and discharges more slowly. In a measurement circuit, a probe’s input capacitance can therefore change the waveform being measured. At higher frequencies, wiring and transmission-line effects require models based on distributed impedance rather than only lumped components.\n\nResonant circuits exhibit a different trade-off. For a lightly damped, isolated resonance, the quality factor is approximately\n\n\\[Q=\\frac{f_0}{B},\\]\n\nwhere \\(f_0\\) is the resonant frequency and \\(B\\) is the half-power bandwidth. High \\(Q\\) gives narrow frequency selectivity but also a longer decay time after excitation. A receiver filter that sharply separates adjacent channels may therefore respond slowly to short pulses. This trade-off appears in radio filters, acoustic resonators, and many spectroscopic instruments.\n\nAn operational amplifier often trades closed-loop gain against bandwidth. For an amplifier whose open-loop response is dominated by one pole, the product of closed-loop gain and bandwidth is approximately constant over a useful operating range. A device with a 10 MHz gain–bandwidth product might therefore provide roughly 1 MHz bandwidth at a noise gain of ten. This approximation does not describe every amplifier architecture, and stability depends on the complete loop response.\n\nSmall-signal bandwidth must also be distinguished from large-signal performance. An amplifier may reproduce a tiny high-frequency sine wave while failing to reproduce a larger one because its output cannot change fast enough. For a sine wave of peak amplitude \\(V_{\\mathrm p}\\), the required maximum slope is \\(2\\pi fV_{\\mathrm p}\\). A slew-rate limit therefore produces an amplitude-dependent full-power bandwidth, separate from the small-signal 3 dB bandwidth.\n\nOscilloscopes, probes, photodetectors, and acquisition systems inherit these limitations. Their combined response, not the headline bandwidth of one component, determines measurement fidelity. For approximately Gaussian responses, component rise times are often combined by a root-sum-square approximation. Other response shapes require a fuller convolution or frequency-domain calculation, particularly when phase distortion, ringing, or sharp spectral cutoffs matter."
    },
    {
      "heading": "Information capacity and the historical theory of communication",
      "text": "The connection between frequency bandwidth and data rate became precise through twentieth-century communication theory. In 1924 and 1928, Harry Nyquist analyzed signaling speed and telegraph transmission. In 1928, Ralph Hartley related information to the number of distinguishable message choices. Claude Shannon’s 1948 paper, “A Mathematical Theory of Communication,” established information theory and a general mathematical framework for communication limits.\n\nFor an ideal noiseless low-pass channel of bandwidth \\(B\\), suitably shaped pulses can convey \\(2B\\) independent real-valued symbols per second without intersymbol interference under the standard Nyquist model. If each symbol has \\(M\\) possible values, the corresponding rate is\n\n\\[R=2B\\log_2 M.\\]\n\nThis expression does not imply unlimited practical transmission by increasing \\(M\\). As levels become more closely spaced, noise and distortion make them harder to distinguish. The ideal noiseless assumption is exactly what removes that constraint from the formula.\n\nFor a band-limited channel with additive white Gaussian noise and an average signal-power constraint, Shannon’s capacity formula is\n\n\\[C=B\\log_2\\left(1+\\frac{S}{N}\\right),\\]\n\nwhere \\(C\\) is capacity in bits per second, \\(B\\) is bandwidth in hertz, and \\(S/N\\) is the received signal-to-noise ratio in linear units. For example, a 3 kHz channel with a 30 dB signal-to-noise ratio has a theoretical capacity of approximately 29.9 kbit/s under this model, since 30 dB corresponds to a power ratio of 1,000.\n\nCapacity is a theoretical boundary, not a guaranteed equipment rate. Shannon’s coding theorem establishes that rates below capacity can, in the ideal asymptotic setting, achieve arbitrarily small error probability with suitable coding and sufficiently long blocks. Practical error-correcting codes operate with finite block lengths, decoding complexity, and delay. Real systems also face synchronization errors, nonlinearities, interference, and channels that vary over time.\n\nIncreasing bandwidth does not necessarily increase capacity in direct proportion. If received signal power \\(S\\) and white-noise density \\(N_0\\) remain fixed, the noise admitted over bandwidth \\(B\\) is \\(N_0B\\). Then\n\n\\[C=B\\log_2\\left(1+\\frac{S}{N_0B}\\right).\\]\n\nAs \\(B\\) tends to infinity, this idealized capacity approaches \\(S/(N_0\\ln 2)\\), rather than growing without bound. More bandwidth admits more signaling dimensions but also more noise.\n\nThese results distinguish three resources: spectrum, power, and coding sophistication. They also explain why a frequency allocation alone cannot determine a service’s data capacity. A narrow, high-quality channel can outperform a wider but severely impaired one, while multiple independently usable spatial channels can raise total capacity without widening the assigned frequency interval."
    },
    {
      "heading": "Modulation, radio spectrum, and optical links",
      "text": "Modulation determines how information is represented on a physical waveform and strongly influences occupied bandwidth. In conventional double-sideband amplitude modulation, a baseband message extending to \\(W\\) hertz produces sidebands extending \\(W\\) hertz above and below the carrier, giving a total transmission bandwidth of \\(2W\\). Single-sideband transmission suppresses one sideband and can convey the same idealized message within approximately \\(W\\), though practical filtering and demodulation introduce additional considerations.\n\nFrequency modulation illustrates why bandwidth cannot always be inferred from a message’s highest frequency alone. A sinusoidally frequency-modulated carrier has infinitely many mathematical sidebands. Carson’s rule estimates a useful occupied bandwidth as\n\n\\[B\\approx 2(\\Delta f+f_{\\mathrm m}),\\]\n\nwhere \\(\\Delta f\\) is peak frequency deviation and \\(f_{\\mathrm m}\\) is the highest relevant modulating frequency. This is an engineering approximation, not a strict spectral boundary.\n\nFor digitally modulated signals, symbol rate and pulse shaping are central. With ideal raised-cosine shaping, a quadrature-modulated carrier signal at symbol rate \\(R_{\\mathrm s}\\) has a nominal passband width\n\n\\[B=(1+\\alpha)R_{\\mathrm s},\\]\n\nwhere \\(\\alpha\\), between zero and one, is the roll-off factor. Higher-order constellations carry more bits per symbol, increasing spectral efficiency, commonly expressed in bit/s/Hz. Their closer-spaced signal points generally require better signal quality or stronger coding.\n\nOrthogonal frequency-division multiplexing divides a channel among many closely spaced subcarriers. Their spectra overlap, but mathematical orthogonality permits separation at the receiver when timing and frequency conditions are maintained. A cyclic prefix helps manage multipath delay spread, at the cost of overhead. Guard bands, pilot signals, coding, and control information further reduce the payload rate relative to a simple multiplication of symbol rate by bits per symbol.\n\nRadio systems share portions of the electromagnetic spectrum, making out-of-band emissions and adjacent-channel interference important. Frequency allocations define where services may operate; channel plans and emission limits constrain how they use those allocations. Multiple-antenna spatial multiplexing can increase data rate within the same assigned band when the propagation environment provides sufficiently independent spatial channels. The gain is not determined by antenna count alone.\n\nIn optical fiber, data are carried by light rather than radio-frequency carriers, but bandwidth remains constrained by transmitter and receiver electronics, optical filtering, dispersion, and nonlinear effects. Wavelength-division multiplexing places multiple optical carriers on one fiber. Aggregate capacity is the sum of usable channel rates, not a synonym for any one channel’s occupied width. A wavelength interval must also be converted carefully to frequency: for a small interval near wavelength \\(\\lambda\\), \\(|\\Delta f|\\approx c|\\Delta\\lambda|/\\lambda^2\\), so equal wavelength spacings do not represent equal frequency spacings across all wavelengths."
    },
    {
      "heading": "Network bandwidth, throughput, and delay",
      "text": "On the Internet and other packet networks, bandwidth most often denotes a link’s nominal data rate or a path’s potential transfer capacity. The observed delivery rate is throughput, while goodput counts useful application data rather than headers, retransmissions, and other overhead. A network interface’s rated speed, a transport connection’s throughput, and an application’s goodput can therefore differ substantially without any contradiction.\n\nFor a simple path of serial links, the lowest-capacity link places an upper bound on sustained end-to-end throughput for a single flow, assuming no alternative paths or parallel transfers. Actual available capacity also depends on competing traffic. A nominal 1 Gbit/s bottleneck does not provide 1 Gbit/s to every user; it provides a total service rate that must be shared according to scheduling, traffic patterns, and protocol behavior.\n\nBandwidth and latency measure different aspects of performance. Transmitting a packet containing \\(L\\) bits onto a link of rate \\(R\\) takes \\(L/R\\) seconds, called serialization delay. A 1,500-byte packet takes 12 microseconds to serialize at 1 Gbit/s, before additional link-layer overhead. Propagation delay depends instead on distance and signal speed. Processing and queueing add further delay. Raising bandwidth shortens serialization time but does not remove the propagation time of a long-distance connection.\n\nReliable transport protocols such as TCP must keep enough data in flight to use a high-capacity path. The relevant scale is the bandwidth–delay product:\n\n\\[D=R\\,T,\\]\n\nwhere \\(T\\) is the round-trip time when the expression is used to estimate the required transport window. At 1 Gbit/s and a round-trip time of 100 ms, the product is 100 Mbit, or 12.5 MB. A much smaller effective window can prevent full utilization even when the physical link is otherwise idle.\n\nCongestion control adjusts sending behavior in response to network conditions. Loss, explicit congestion signals, measured delay, receiver limits, and implementation details can all affect achieved throughput. Large queues may sustain utilization while adding substantial delay, a condition often called bufferbloat. Consequently, a high download rate does not by itself establish that a connection will perform well for interactive traffic.\n\nCommercial and operational bandwidth figures also refer to different boundaries. An access service may advertise separate downstream and upstream rates; a switching device may quote the sum of several ports; a shared access network may rely on statistical multiplexing. A full-duplex 1 Gbit/s link can transmit in both directions simultaneously, but calling it “2 Gbit/s aggregate” does not make either one-way transfer run at 2 Gbit/s. Meaningful comparisons require matching direction, protocol layer, sharing conditions, and measurement interval."
    },
    {
      "heading": "Memory, interconnects, and computational performance",
      "text": "In computer architecture, bandwidth describes how rapidly data can move between processors, memory, storage, and peripheral devices. It is usually expressed in bytes per second. A memory interface’s theoretical bandwidth is the product of its transfer rate and the amount of data transferred in parallel. An interface operating at 3,200 million transfers per second over a 64-bit data path has a nominal bandwidth of 25.6 GB/s, before accounting for the system’s transaction patterns and operating constraints.\n\nClock frequency is not necessarily the transfer rate. Double-data-rate interfaces transfer data on both edges of a clock, and other interfaces use additional signaling or encoding arrangements. Error-correction bits, packet headers, command cycles, and line coding may consume physical resources without delivering application data. Specifications must therefore distinguish raw signaling rate, interface payload rate, and sustained useful bandwidth.\n\nMemory latency and memory bandwidth are separate limitations. A single dependent pointer-chasing operation may wait for each access to complete before issuing the next, making latency dominant. A program processing many independent array elements can issue multiple memory requests concurrently and approach a bandwidth limit. Cache lines, prefetching, bank parallelism, and the number of outstanding requests determine whether the hardware can keep enough transfers active.\n\nAccess pattern matters as much as nominal capacity. Sequential accesses use cache lines efficiently and are often predictable enough for prefetching. Random accesses may transfer entire lines while using only a few bytes. Writes may involve allocation, coherence traffic, or later writeback, so the data moved across an interface can exceed the number of bytes explicitly written by a program. In multiprocessor systems, memory placement and interconnect topology also affect which bandwidth is available to a particular core.\n\nThe roofline model connects data movement to computation:\n\n\\[P\\leq \\min\\left(P_{\\mathrm{peak}},\\,B_{\\mathrm{mem}}I\\right),\\]\n\nwhere \\(P\\) is computational performance, \\(P_{\\mathrm{peak}}\\) is peak arithmetic performance, \\(B_{\\mathrm{mem}}\\) is sustainable memory bandwidth, and \\(I\\) is arithmetic intensity, measured as operations per byte transferred at a specified memory level. Low-intensity algorithms are often bandwidth-bound; high-intensity algorithms may instead be limited by computation.\n\nThis model explains why additional arithmetic units do not automatically accelerate every workload. A simple operation on large arrays may move many bytes for each calculation, while blocked matrix multiplication reuses data extensively and performs many operations per fetched value. Machine-learning workloads can shift between these regimes depending on batch size, numerical precision, model structure, and whether weights remain in fast memory. The bandwidth of main memory, on-chip caches, accelerator interconnects, and storage represents different constraints, so a single “system bandwidth” number rarely predicts overall performance."
    },
    {
      "heading": "Measurement methods and interpretation",
      "text": "Frequency bandwidth is measured using methods suited to either a system response or a signal spectrum. A vector network analyzer applies swept or otherwise controlled test signals and measures complex responses such as transmission and reflection. A filter’s bandwidth can then be obtained from its measured transmission magnitude using a specified threshold. Phase measurements reveal delay and dispersion that an amplitude-only bandwidth figure omits.\n\nA spectrum analyzer estimates how signal power is distributed with frequency. Its resolution bandwidth is an instrument setting or effective analysis width, not necessarily the bandwidth of the signal under test. A narrower resolution bandwidth can separate nearby spectral components and reduce displayed noise per measurement bin, but it generally requires a longer observation or sweep. Detector type, averaging, windowing, and analyzer overload can change the apparent spectrum.\n\nFinite observation time imposes additional limits. A record of duration \\(T\\) has a basic Fourier-bin spacing of \\(1/T\\), although actual spectral resolution also depends on the analysis window. Abruptly truncating a record spreads energy from a tone into neighboring bins, a phenomenon called spectral leakage. Window functions reduce leakage at the cost of a broader main lobe and altered equivalent noise bandwidth. Bin spacing, resolvable frequency separation, and occupied signal bandwidth are therefore different quantities.\n\nNetwork bandwidth measurements are similarly conditional. A transfer test records performance between particular endpoints, over a particular route, with a particular traffic pattern. Disk speed, processor load, encryption, receiver limits, and server capacity may become bottlenecks before the network does. Multiple parallel flows can sometimes approach aggregate path capacity when a single flow cannot, but the result then describes a different workload.\n\nPassive monitoring measures traffic already present, while active testing injects traffic to estimate capacity, available bandwidth, delay, or loss. Observing low utilization does not establish low capacity: the sender may simply have little data to transmit. Conversely, a short burst rate can exceed a long-term service rate when buffering or traffic-shaping policies permit bursts. Sustained measurements and time-resolved measurements answer different operational questions.\n\nReliable reporting identifies the bandwidth definition, units, reference plane, direction, test duration, and relevant operating conditions. Instrument results also depend on calibration and measurement uncertainty. A 3 dB bandwidth measured with unmatched impedances, a throughput result that includes retransmitted bytes, and a memory benchmark dominated by cache hits may each be internally valid while failing to represent the quantity implied by an unqualified bandwidth label."
    }
  ],
  "links": [
    "second",
    "international-system-of-units",
    "fourier-transform",
    "decibel",
    "signal-processing",
    "uncertainty-principle",
    "sampling-theorem",
    "aliasing",
    "capacitance",
    "electrical-impedance",
    "information-theory",
    "signal-to-noise-ratio",
    "error-correcting-code",
    "modulation",
    "electromagnetic-spectrum",
    "optical-fiber",
    "light",
    "wavelength-division-multiplexing",
    "internet",
    "latency",
    "roofline-model",
    "machine-learning",
    "calibration",
    "measurement-uncertainty"
  ],
  "sources": [],
  "license": "https://creativecommons.org/licenses/by/4.0/"
}