{
  "id": "azeotrope",
  "title": "Azeotrope",
  "lang": "en",
  "source_lang": "en",
  "summary": "An azeotrope is a mixture that boils at a particular composition without changing the overall composition of the vapor produced.",
  "category": "science",
  "subcategory": "chemistry",
  "type": "concept",
  "aliases": [
    "Azeotropic mixture",
    "constant-boiling mixture"
  ],
  "generated_at": "2026-11-05",
  "model": "pro/gpt-6.1-sol",
  "url": "https://aiwiki.page/en/azeotrope/",
  "translations": {
    "zh-Hans": {
      "url": "https://aiwiki.page/zh/azeotrope/",
      "json": "https://aiwiki.page/zh/azeotrope.json"
    }
  },
  "sections": [
    {
      "heading": "",
      "text": "An azeotrope is a mixture of two or more components that, at a specified pressure, boils with a vapor composition identical to the overall composition of the boiling liquid or liquid phases. At this composition, boiling does not preferentially remove one component, so ordinary distillation cannot separate the mixture further. Azeotropy is a property of phase equilibrium, not evidence that the components have formed a new chemical compound. Its occurrence and composition depend on pressure and on interactions between the components."
    },
    {
      "heading": "Phase-equilibrium basis",
      "text": "For most liquid mixtures, the vapor produced during boiling has a different composition from the liquid. This difference permits separation by distillation: repeated vaporization and condensation enrich the vapor-derived product in the more volatile component.\n\nAt a homogeneous azeotrope, where only one liquid phase is present, the equilibrium vapor and liquid have the same composition:\n\n\\[y_i=x_i\\]\n\nfor every component \\(i\\), where \\(x_i\\) and \\(y_i\\) are the liquid-phase and vapor-phase mole fractions. The mixture consequently boils at constant composition and temperature while pressure remains fixed.\n\nThe more general requirement is equality of the chemical potential of each component in coexisting phases. For vapor–liquid equilibrium,\n\n\\[\\mu_i^{\\mathrm{L}}=\\mu_i^{\\mathrm{V}}.\\]\n\nThis equilibrium condition applies to both azeotropic and nonazeotropic mixtures; azeotropy adds the special requirement of matching phase compositions in a homogeneous system.\n\nAzeotropic composition must be specified on a clear basis. Mass percentage, mole fraction, and volume percentage are not interchangeable. An azeotrope specified at one pressure also need not retain that composition at another pressure."
    },
    {
      "heading": "Molecular origin and thermodynamic description",
      "text": "Azeotropes arise from sufficiently strong departures from ideal liquid-mixture behavior. In an ideal mixture, Raoult’s law relates each component’s partial vapor pressure to its liquid mole fraction and pure-component saturation vapor pressure. For a nonideal liquid in equilibrium with an approximately ideal vapor, a common extension is\n\n\\[y_iP=x_i\\gamma_iP_i^{\\mathrm{sat}}(T),\\]\n\nwhere \\(P\\) is total pressure, \\(P_i^{\\mathrm{sat}}\\) is the saturation vapor pressure of pure component \\(i\\), and \\(\\gamma_i\\) is its activity coefficient in the liquid.\n\nAt a homogeneous azeotrope, substitution of \\(y_i=x_i\\) gives, for each component present,\n\n\\[P=\\gamma_iP_i^{\\mathrm{sat}}(T).\\]\n\nThus the effects of liquid composition and nonideality exactly compensate for the components’ different pure-component vapor pressures. At higher pressures, vapor-phase nonideality and pressure corrections may also be important.\n\nFor a binary mixture, the relative volatility is commonly defined as\n\n\\[\\alpha_{12} =\\frac{y_1/x_1}{y_2/x_2}.\\]\n\nAt the azeotropic composition, \\(\\alpha_{12}=1\\): neither component is more volatile than the other in the separation sense.\n\nNonideal behavior reflects differences among like-molecule and unlike-molecule interactions, including hydrogen bonding, dispersion forces, and changes in molecular association. The relevant thermodynamics involves both enthalpic and entropic contributions to mixing; azeotropy cannot generally be predicted from a simple comparison of intermolecular attraction strengths alone."
    },
    {
      "heading": "Main types",
      "text": "Minimum-boiling azeotropes\n\nA minimum-boiling azeotrope boils at a lower temperature than either pure component at the same pressure. It is associated with sufficiently strong positive deviations from Raoult’s law: the mixture has a greater vapor pressure than ideal-mixture behavior would predict.\n\nThe ethanol–water system is a familiar example. At approximately standard atmospheric pressure, its azeotrope contains about 95.6% ethanol by mass and boils near 78.2 °C. The ethanol mole fraction is approximately 0.895. These figures should not be confused with ethanol volume percentages.\n\nFor a simple binary system with one minimum-boiling azeotrope, fractionation tends to concentrate the azeotrope in the overhead product. Which component can remain as a purified bottoms product depends on the feed’s position relative to the azeotropic composition.\n\nMaximum-boiling azeotropes\n\nA maximum-boiling azeotrope boils at a higher temperature than either pure component at the same pressure. It is associated with sufficiently strong negative deviations from Raoult’s law, giving a lower vapor pressure than predicted for an ideal mixture.\n\nHydrogen chloride–water provides a standard example. At approximately standard atmospheric pressure, its maximum-boiling azeotrope contains about 20.2% hydrogen chloride by mass and boils near 108.6 °C.\n\nIn a simple binary system of this kind, fractionation tends to retain the azeotropic composition in the bottoms while removing a more volatile product overhead.\n\nHomogeneous and heterogeneous azeotropes\n\nA homogeneous azeotrope has a single liquid phase in equilibrium with its vapor.\n\nA heterogeneous azeotrope, or heteroazeotrope, involves two coexisting liquid phases and a vapor phase. On condensation, the vapor can separate into two liquid layers with different compositions. The vapor composition is not generally identical to the composition of either individual liquid layer. Constant-composition boiling is possible when the combined liquid inventory has the appropriate overall composition and both liquid phases remain present.\n\nThis distinction is important: the simple relation \\(y_i=x_i\\) describes a homogeneous azeotrope, not the individual liquid phases of a heterogeneous one. Water–toluene is a familiar heterogeneous azeotropic system.\n\nBinary and multicomponent azeotropes\n\nAzeotropes may involve two components, three components, or more. Multicomponent systems can contain several binary and ternary azeotropes, producing complicated separation boundaries. Some multicomponent azeotropes have saddle-type behavior rather than being simple overall boiling-temperature minima or maxima.\n\nA liquid pair can also exhibit more than one azeotrope under certain conditions. The presence of nonideal behavior alone, however, does not guarantee that any azeotrope exists."
    },
    {
      "heading": "Phase diagrams and experimental identification",
      "text": "For a binary homogeneous mixture at fixed pressure, a temperature–composition diagram displays a bubble-point curve, marking the onset of boiling, and a dew-point curve, marking the onset of condensation. At an azeotrope, these curves meet at an interior composition where the equilibrium liquid and vapor compositions coincide.\n\nOn a vapor-composition versus liquid-composition plot, an azeotrope appears where the equilibrium curve meets the diagonal \\(y=x\\) at a composition other than a pure-component endpoint.\n\nExperimental identification requires equilibrium measurements of temperature, pressure, and both liquid and vapor composition. Chromatography and other analytical methods can determine the phase compositions. A nearly constant boiling temperature by itself is not conclusive evidence of azeotropy: a narrow-boiling nonazeotropic mixture can show similar behavior over a limited composition range.\n\nBecause the separation driving force becomes small near an azeotrope, distinguishing exact azeotropy from near-azeotropic behavior requires attention to measurement uncertainty."
    },
    {
      "heading": "Consequences for separation",
      "text": "An azeotrope is a thermodynamic limitation on ordinary equilibrium distillation at fixed pressure, not a universal prohibition on separating its components. Adding more equilibrium stages or increasing reflux cannot make a conventional binary distillation cross the azeotropic composition under unchanged conditions.\n\nSeveral processes circumvent this limitation.\n\n- Pressure-swing distillation: If azeotropic composition changes sufficiently with pressure, columns operating at different pressures can achieve separation through suitable recycle arrangements. Not every azeotropic system shifts enough for this method to be practical.\n- Azeotropic distillation: An added component, often called an entrainer, changes the phase-equilibrium behavior and may create a new azeotrope that facilitates removal of one component.\n- Extractive distillation: A relatively low-volatility solvent alters the components’ relative volatility. The solvent is subsequently recovered for reuse; the method does not require formation of a new azeotrope.\n- Adsorption: Selective adsorption, including water removal by molecular sieves, separates components without depending on their relative volatility.\n- Membrane separation: Processes such as pervaporation combine selective transport through a membrane with vapor removal, providing a separation mechanism different from ordinary vapor–liquid equilibrium.\n\nProcess selection depends on equilibrium behavior, purity requirements, energy consumption, solvent recovery, materials compatibility, and environmental constraints."
    },
    {
      "heading": "Applications and distinctions",
      "text": "Azeotropy is important in solvent recovery, alcohol production, chemical purification, and the design of distillation systems. Heterogeneous azeotropic distillation can facilitate water removal because the condensed overhead separates into liquid layers, allowing selective withdrawal and recycle.\n\nAzeotropic and near-azeotropic refrigerant blends are also useful where a small temperature change during evaporation or condensation is desirable. An exact azeotrope has no equilibrium temperature glide at its azeotropic composition and specified pressure; a near-azeotropic blend has a small but nonzero glide.\n\nAn azeotrope should be distinguished from several related concepts:\n\n- A pure substance has a single chemical identity; an azeotrope contains multiple components whose identities remain distinct.\n- A zeotropic mixture has differing equilibrium liquid and vapor compositions and generally changes composition during boiling.\n- A eutectic concerns solid–liquid equilibrium and melting behavior, rather than the vapor–liquid equilibrium responsible for azeotropy.\n- A constant-boiling sample is not necessarily an azeotrope unless its equilibrium composition behavior has also been established."
    }
  ],
  "links": [
    "pressure",
    "distillation",
    "condensation",
    "temperature",
    "chemical-potential",
    "raoults-law",
    "activity-coefficient",
    "hydrogen-bond",
    "thermodynamics",
    "ethanol",
    "water",
    "chromatography",
    "measurement-uncertainty",
    "solvent",
    "adsorption"
  ],
  "sources": [],
  "license": "https://creativecommons.org/licenses/by/4.0/"
}