{
  "id": "atmospheric-water-harvesting",
  "title": "Atmospheric Water Harvesting",
  "lang": "en",
  "source_lang": "en",
  "summary": "Atmospheric water harvesting collects airborne droplets or extracts water vapor from air through cooling, sorption, or combinations of these processes.",
  "category": "technology",
  "subcategory": "engineering",
  "type": "concept",
  "aliases": [
    "Atmospheric water collection",
    "atmospheric water capture",
    "water harvesting from air"
  ],
  "generated_at": "2026-11-05",
  "model": "pro/gpt-6.1-sol",
  "url": "https://aiwiki.page/en/atmospheric-water-harvesting/",
  "translations": {
    "zh-Hans": {
      "url": "https://aiwiki.page/zh/atmospheric-water-harvesting/",
      "json": "https://aiwiki.page/zh/atmospheric-water-harvesting.json"
    }
  },
  "sections": [
    {
      "heading": "",
      "text": "Atmospheric water harvesting (AWH) is the collection of water from the atmosphere, either by intercepting suspended liquid droplets or by extracting water vapor. Its principal approaches are fog collection, dew condensation, mechanically refrigerated condensation, and sorption using moisture-attracting materials. These approaches differ substantially in their energy requirements, climatic suitability, and water output. Atmospheric water harvesting can provide a supplementary or decentralized supply, but its usefulness depends on local weather, available energy, maintenance requirements, and the quality of the collected water."
    },
    {
      "heading": "Physical basis",
      "text": "Air contains water vapor in amounts that vary with temperature and weather conditions. Relative humidity is the ratio of water-vapor partial pressure to saturation vapor pressure at the same temperature. It indicates how close air is to saturation, but does not by itself specify how much water is available: warm air at moderate relative humidity can contain more vapor per unit volume than cold air at high relative humidity.\n\nThe dew point is the temperature at which air becomes saturated when cooled at approximately constant pressure without changing its water-vapor content. Cooling a surface below the surrounding air’s dew point allows vapor to condense on it. Alternatively, a sorbent can take up vapor without first cooling the bulk air below its dew point.\n\nFog collection is physically different. Fog already contains liquid droplets, so a collector mainly separates these droplets from moving air rather than converting vapor into liquid. This distinction explains why a well-sited fog collector can operate with little external energy, while an active vapor-extraction system usually needs a substantial energy input.\n\nThe water inventory in air is relatively dilute. At approximately \\(20\\,^\\circ\\mathrm{C}\\) and 50% relative humidity, air contains about 8.6 grams of water vapor per cubic meter. Even with complete extraction, producing one liter of water would therefore require processing roughly 116 cubic meters of that air. Practical systems must process more because extraction is incomplete and operating conditions fluctuate."
    },
    {
      "heading": "Main approaches",
      "text": "Fog collection\n\nFog collectors typically consist of mesh panels installed across prevailing fog-bearing winds. Droplets collide with fibers, merge into larger drops, and drain into gutters and storage tanks. Wind supplies the airflow, while gravity moves the collected liquid.\n\nPerformance depends on fog liquid-water content, droplet size, wind speed, mesh geometry, and surface properties. A mesh must balance several competing effects: closely spaced fibers can intercept droplets effectively but can also divert airflow around the collector, while retained water can obstruct openings or be blown away.\n\nFog collection is most useful where frequent fog coincides with favorable terrain and winds, including some coastal mountain environments. It does not produce substantial water merely because the air is humid. Reported yields are therefore highly site-specific and may vary sharply between seasons.\n\nPassive dew collection\n\nDew collectors use surfaces that cool below the dew point, often through nighttime radiative cooling to the sky. Suitable surfaces emit thermal radiation efficiently and limit heat gain from the air, the ground, or supporting structures.\n\nClear skies, sufficiently humid air, and limited unwanted heat transfer favor dew formation. Clouds reduce radiative heat loss to the sky, while strong wind can warm a surface that has cooled below ambient temperature. Tilted panels allow droplets to drain into a collection channel.\n\nPassive dew systems require little operating energy, but their output per unit area is generally limited. Condensation releases heat, which the collector must reject while remaining below the dew point. Large collection areas may therefore be needed for modest water production.\n\nRefrigeration-based condensation\n\nAn active atmospheric water generator commonly uses vapor-compression refrigeration to cool an air-contacting coil below the dew point. A fan moves air across the coil, condensate drains into a tank, and the refrigeration system rejects heat elsewhere.\n\nThis arrangement resembles a dehumidifier or air conditioner, although equipment intended to supply drinking water also requires appropriate collection surfaces, treatment, and storage controls. Recovering condensate from an existing air-conditioning system is a related approach: water becomes a by-product of cooling rather than the sole purpose of the energy consumption.\n\nRefrigeration-based production is generally more favorable in warm, humid conditions. In cool or dry air, less water is available, greater cooling may be necessary, and frost can interfere with operation. A heat exchanger can recover cooling from outgoing air to precool incoming air, although pressure losses, fouling, and equipment complexity affect the benefit.\n\nThermoelectric cooling can also produce condensate. Its compactness and absence of a mechanical compressor can be useful in small devices, but energy efficiency often limits its suitability for larger water supplies.\n\nSorption-based harvesting\n\nSorption systems use materials that attract water vapor. Solid surfaces can retain water through adsorption, while liquid desiccants take it into their bulk through absorption. Porous materials may also hold water through pore filling and related mechanisms.\n\nA typical cyclic system has two stages:\n\n- Uptake: a sorbent captures atmospheric moisture.\n- Regeneration and recovery: heating or another change in operating conditions releases the water, which is then condensed and collected.\n\nCandidate materials include zeolites, silica gels, hygroscopic salts, metal–organic frameworks, and hydrogels. Salts can be embedded in a polymer or porous support to improve handling and limit leakage.\n\nMaterial performance depends on more than maximum water uptake. Relevant properties include uptake at the intended humidity, the fraction released during regeneration, regeneration temperature, heat of sorption, transport rates, stability, and cost. A material that binds water strongly may capture moisture in dry air but require more demanding regeneration.\n\nSome designs use nighttime uptake followed by daytime heating from solar energy. Others alternate multiple beds or operate continuously. Sorbent regeneration alone does not deliver liquid water: the released vapor must reach a condenser under conditions that permit condensation."
    },
    {
      "heading": "Energy and transport requirements",
      "text": "Atmospheric water extraction is a separation process governed by thermodynamics, heat transfer, and mass transfer. Water vapor must reach a collection surface or sorbent, and the associated heat must be managed.\n\nFor a continuous-flow condensation unit, an approximate water balance is\n\n\\[\\dot m_w=\\dot m_{da}(\\omega_{\\mathrm{in}}-\\omega_{\\mathrm{out}}),\\]\n\nwhere \\(\\dot m_w\\) is the water collection rate, \\(\\dot m_{da}\\) is the dry-air mass flow rate, and \\(\\omega\\) is the humidity ratio, expressed as water-vapor mass per unit mass of dry air. The equation shows why high airflow alone does not guarantee high output: the change in humidity ratio is equally important.\n\nNear ordinary ambient temperatures, condensing one kilogram of water releases roughly 2.4 megajoules of latent heat, equivalent to about 0.67 kilowatt-hours of thermal energy. This is not a universal minimum electricity requirement. A refrigeration system moves heat rather than converting electricity directly into cooling, and its electricity demand depends on its coefficient of performance. It must also handle sensible cooling of air, fan power, losses, and any treatment equipment.\n\nSorption systems require regeneration energy and heat rejection during water recovery. Heat recovery can reduce consumption, while slow transport through a sorbent bed can limit production even when equilibrium uptake is high.\n\n“Passive” and “solar-powered” describe aspects of energy supply, not the absence of energy requirements. Solar-driven systems still need collection area and suitable weather, and some also use electrically powered fans, pumps, or controls."
    },
    {
      "heading": "Development and applications",
      "text": "Dew collection has long been recognized as a means of obtaining small quantities of water. Engineered fog collection expanded during the twentieth century through field projects in fog-prone coastal and mountain regions. Modern refrigeration technology enabled active atmospheric water generators, while research into advanced sorbents, particularly during the 2010s and afterward, broadened interest in extraction under lower-humidity conditions.\n\nApplications include remote facilities, small settlements, off-grid equipment, emergency installations, and supplementary supplies where conventional delivery is difficult. Fog collection has a distinct role in locations where fog is frequent but rainfall or accessible freshwater is limited. Building-scale condensate recovery can supplement nonpotable water supplies where cooling loads and humidity are high.\n\nLarge-scale irrigation is more demanding because agricultural water consumption is high relative to the output of many atmospheric systems. Suitability depends on crop value, local water alternatives, climate, and the required collection area and energy supply.\n\nAWH differs from desalination because it processes air rather than saline water. Where seawater and suitable infrastructure are accessible, desalination often requires substantially less electricity per unit of water than standalone refrigerated atmospheric extraction. Atmospheric systems may nevertheless offer logistical advantages where neither a liquid-water source nor a supply pipeline is available."
    },
    {
      "heading": "Water quality",
      "text": "Atmospheric condensate is not automatically drinking water. Air can carry particles, microorganisms, sea salt, and gaseous contaminants. Some contaminants enter collected water directly; others originate from corrosion, coatings, tubing, sorbents, or storage vessels.\n\nQuality depends on both the collection mechanism and the surrounding environment. Fog droplets can incorporate airborne pollutants before reaching a mesh. Refrigerated coils and drain systems can accumulate deposits and biological growth. Sorption systems must prevent desiccant carryover and unwanted release of material constituents.\n\nLow dissolved-mineral content does not establish microbiological or chemical safety. Systems intended to supply drinking water commonly include treatment and storage safeguards, with performance assessed against applicable water-quality requirements. Treatment requirements also affect cost, maintenance, and net usable output."
    },
    {
      "heading": "Performance assessment and limitations",
      "text": "Meaningful comparison requires operating conditions and system boundaries to be stated. Important measures include:\n\n- Net water output, after losses, cleaning, and treatment.\n- Specific electricity consumption, usually in kilowatt-hours per liter or cubic meter.\n- Thermal energy consumption, reported separately from electricity.\n- Area-normalized yield, particularly for fog meshes, dew panels, and solar collectors.\n- Sorbent productivity, distinguishing uptake capacity from recovered liquid-water output.\n- Availability, including seasonal variation, downtime, and replacement requirements.\n- Delivered-water cost, including equipment, energy, treatment, labor, and storage.\n\nA laboratory result at fixed temperature and humidity does not establish year-round field performance. Likewise, high uptake per kilogram of sorbent does not necessarily imply high daily output: cycle duration, regeneration completeness, condenser conditions, and inactive structural mass all matter.\n\nThe regions with the greatest water shortages are not necessarily those with the most favorable atmospheric resource. Dry inland locations may have both low vapor concentrations and high demand. During drought, changes in humidity or fog occurrence can further reduce production.\n\nEnvironmental impacts include electricity supply, refrigerant leakage, material manufacturing, and waste from maintenance and component replacement. Powering equipment with renewable energy can reduce operating emissions, but does not remove requirements for generation capacity, storage, or collector area. Scaling passive collection can also raise land-use and ecological questions where fog contributes moisture to vegetation. These constraints make local resource measurements and full-system performance more informative than nominal output ratings alone."
    }
  ],
  "links": [
    "water",
    "temperature",
    "relative-humidity",
    "dew-point",
    "vapor-compression-refrigeration",
    "air-conditioning",
    "heat-exchanger",
    "thermoelectric-cooling",
    "adsorption",
    "absorption-chemical-engineering",
    "zeolite",
    "metal-organic-framework",
    "hydrogel",
    "polymer",
    "solar-energy",
    "thermodynamics",
    "mass-transfer",
    "coefficient-of-performance",
    "irrigation",
    "desalination",
    "renewable-energy"
  ],
  "sources": [],
  "license": "https://creativecommons.org/licenses/by/4.0/"
}